Hifiverse

Power amplifiers stereo - Aavik Aavik P-880

Description, images, technical data and specifications

Aavik Aavik P-880
Image source - (c) Aavik

The Aavik P-880 is a stereo power amplifier from Aavik of Audio Group Denmark and the power section of the 880 series. Aavik created it, together with the C-880 control amplifier, by dividing the I-880 integrated amplifier into two units. The primary development goal was a non-switching pure class A power amplifier with the lowest possible output impedance. Electronics come from Michael Børresen, and the exterior is the work of Flemming Erik Rasmussen, founder of Gryphon Audio, who joined the Aavik design team in mid-2021. It is handcrafted in Denmark.

Key specs that matter

Output is 2 x 250 W into 8 ohms and 2 x 500 W into 4 ohms. THD is below 0.007% (10 W, 1 kHz, 8 ohms). There is one set of single-ended RCA inputs with 6 kohms input impedance, and gain is adjustable from 25 to 34 dB (31 dB default). Noise reduction comprises 182 active Tesla coils, 411 active square Tesla coils, 18 dither circuits, 20 active zirconium anti aerial resonance Tesla coils and 4 active zirconium cable anti aerial resonance Tesla coils. Consumption is 1 W in standby and 150 W at idle, and mains voltage is 100 - 240 V AC. Dimensions are 580 x 510 x 155 mm (L x W x H), and weight is 41 kg.

Engineering and use context

Its bias circuit keeps the bias spread 0.63 V above the required current at every point of the cycle, and Aavik states that the amplifier stays in class A up to 2 x 200 W into 8 ohms. The capacitors are smaller units placed locally, and each of the eight pairs of output transistors has its own capacitor bank right next to it. Four 500 W power factor corrected resonant mode power supplies are used, and Aavik quotes peak currents in excess of 80 A.

Copper is the base material of the enclosure. Aavik lists lower hysteresis, lower output impedance, lower inductance and cooler operation as the reasons for the solid copper case. Cooling elements are formed on the sides and the top. The bottom plate is a sandwich of a copper plate, a heavy compact laminate plate and a titanium layer. A third generation of the Ansuz analog dither technology is used here. Protection circuits disable the speaker outputs on DC, over current or high temperature.

Pairing

A preamplifier with single-ended RCA outputs is required. The matching control amplifier is the Aavik C-880. Adjustable gain allows level matching in bi-amping or home-theatre systems, and two DC trigger connectors accept 5 - 24 V DC. Speaker terminals take spade connectors or 4 mm banana plugs.

Alternatives

The Aavik P-580 is another stereo power amplifier from Aavik, rated 2 x 300 W into 8 ohms and 2 x 600 W into 4 ohms.

Specifications

  • Model name

    Aavik P-880

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    2 x 250

  • Output power (4Ω) (W)

    2 x 500

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    N/A

  • Signal to Noise Ratio (dB)

    N/A

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    <0,007

  • Max power consumption (W)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    580 x 510 x 155

  • Weight (kg)

    41

  • Official link

Related content

More components