Hifiverse

Power amplifiers mono — Burson Audio Timekeeper Voyager

Description, images, technical data and specifications

Burson Audio Timekeeper Voyager
Image source - (c) Burson Audio

The Timekeeper Voyager is a monoblock power amplifier from Burson Audio, the Australian maker of compact amplifiers and discrete opamps based in Melbourne. Burson lists it as a 200 W Class-AB monoblock with a selectable input buffer, sold in pairs with an external power supply. It belongs to the Voyager series, which sits above the GT4 and Stellar series in Burson's range, and Burson has developed Timekeeper amplifiers for over fifteen years. The Standard package was priced at USD 5,000 and the Max package at USD 6,000.

Key specs that matter

Output power is 100 W into 8 ohms and 200 W into 4 ohms per monoblock. Gain is 29 dB. Input impedance is 100 kohms single-ended and 200 kohms balanced. Frequency response is 20 Hz - 20 kHz, THD is below 0.03% at 1 kHz, and signal-to-noise ratio is 110 dB. Output impedance is below 0.015 ohms from 20 Hz to 20 kHz. With the input buffer on, gain rises by 12 dB on XLR and 6 dB on RCA. Idling power is 100 W, and standby power is below 1 W. Each monoblock has one RCA and one XLR input and a pair of speaker binding posts, measures 265 x 270 x 85 mm and weighs about 7 kg.

Engineering and use context

This is a fully discrete, high-current design. Drawing over 100 W at idle, it runs in its most linear zone, according to Burson. Its output transistors are UK-made FETs. The switchable input buffer operates in class A with Burson's V7 Vivid Pro discrete opamps, and the opamps can be swapped by the owner. Silent Power 02 regulator modules have a noise floor of 0.8 µV, which Burson quotes as 200 times lower than standard regulators.

Power comes from an external supply. In the Standard package two monoblocks share a Burson Super Charger 32 V/7 A supply, while the Max package has two Fusion Core 32 V/15 A supplies. Fusion Core uses GaN transistors switching at 1 MHz and delivers up to 480 W, with a noise floor below 1 µV and an input range of 100-240 V AC. With one amplifier per channel there is no crosstalk between channels. Burson's Cool Case chassis is made of 6 mm high-density aluminium panels and acts as the heat sink, so no separate heat sinks are used. Finishes are copper-gold and space grey, and registered products carry a three-year warranty.

Pairing

Burson names Dynaudio, B&W and KEF loudspeakers as loads for the Voyager. With the buffer on, a DAC with its own volume control can be connected directly. With a separate preamplifier in the system the buffer is switched off.

Alternatives

The Timekeeper GT4 is Burson's other 200 W Class-AB monoblock, with a higher-voltage power supply and British-made Exicon MOSFET output transistors.

Specifications

  • Model name

    Timekeeper Voyager

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    N/A

  • Output power (4Ω) (W)

    200

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    N/A

  • Signal to Noise Ratio (dB)

    N/A

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    N/A

  • Max power consumption (W)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    N/A

  • Weight (kg)

    N/A

  • Official link

Related content