Hifiverse

Power amplifiers mono — Vincent SP-T700

Description, images, technical data and specifications

Vincent SP-T700
Image source - (c) Vincent

The SP-T700 is a mono power amplifier from Vincent, the German brand of Sintron Vertriebs GmbH in Iffezheim. Vincent calls it a monaural Class A tube power amplifier. It is a hybrid of tubes and transistors, developed by Vincent as a completely new combination amplifier. One unit drives one or two loudspeakers on a single channel, so two are required for stereo.

Key specs that matter

Nominal output power is 150 W RMS into 8 ohms and 300 W RMS into 4 ohms, of which 10 W into 8 ohms is in Class A. Frequency response is 20 Hz - 20 kHz (±0.5 dB). Total harmonic distortion is below 0.01% (1 kHz, 1 W) and below 0.1% (1 kHz, 25 W). Signal-to-noise ratio is above 90 dB, and intermodulation (DIN IEC268) is above 90 dB (60 Hz and 7 kHz mixed 4 to 1, 1 W). Input sensitivity is 1 V for 25 W RMS into 4 ohms, with an input impedance of 22 kohms. Tube complement is one 6S3P-EV, one 6SCH9P and one 6Z4. Maximum power consumption is 306 W. Dimensions are 210 x 263 x 400 mm (W x H x D), and weight is 16 kg.

Engineering and use context

Vincent specifies 100% selected frame-grid tubes from the military sector, with a design lifetime of 10,000 hours. The transistor stage of the SP-T700 works in Class A mode. On the front panel the tubes sit behind a display window, and a rear DIMMER switch sets the brightness of the tube illumination.

Each chassis has two pairs of threaded speaker terminals, A and B, that take 4 mm banana plugs and carry the same mono signal. Front-panel SPEAKER A/B buttons switch each pair on and off, with an LED beside each button. Input is one mono RCA LINE IN for a preamplified signal. Two 3.5 mm POWER CONTROL (12 V) jacks receive and pass on the trigger signal, and a POWER CONTROL cable is included. A voltage selector behind a rear pane changes the mains setting from 230 V to 110 V, and Vincent restricts this to a technician. Black and silver finishes are offered.

Pairing

A preamplifier with RCA pre-outputs is required, one output per amplifier. Loudspeakers with a nominal impedance of at least 4 ohms are required. The matching Vincent preamplifier is the SA-T7.

Alternatives

The SP-332 is a Vincent stereo hybrid power amplifier of the powerLine, with an input stage of two 6N16 tubes.

Specifications

  • Model name

    SP-T700

  • Input sensitivity (mV)

    1000

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    22 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    150

  • Output power (4Ω) (W)

    300

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    20

  • Frequency response high +/- 3dB (Hz)

    20 000

  • Signal to Noise Ratio (dB)

    >90

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    <0.01

  • Max power consumption (W)

    306

  • Damping factor

    N/A

  • Dimensions (mm)

    210 x 263 x 400

  • Weight (kg)

    16

  • Official link