Hifiverse

Power amplifiers mono - Cary Audio SA-500.1 ES

Description, images, technical data and specifications

Cary Audio SA-500.1 ES
Image source - (c) Cary Audio

The SA-500.1 ES is a solid-state mono power amplifier from Cary Audio, announced in April 2018 at USD 4,995. Cary designs and builds it at its factory in North Carolina. It is the next generation of the original SA-500.1, a clean-sheet design that was a departure from traditional Cary amplifier design. According to the Cary white paper, the SA-500.1 ES is essentially a bridged SA-200.2 ES with a balanced or single-ended input.

Key specs that matter

Circuit type is solid state, class A/B. Rated output is 1 x 500 W into 8 ohms and 1 x 1000 W into 4 ohms, both from 20 Hz to 20 kHz. Frequency response is 10 Hz - 50 kHz (±0.1 dB). Voltage gain is 28 dB, and input impedance is 30 kohms on both the RCA and the XLR input. Signal-to-noise ratio is better than 100 dB (A-weighted), THD is less than 0.05% at rated output, and the damping factor is greater than 400 from 10 Hz to 20 kHz. Cary specifies 3 dB of dynamic headroom and stability into low impedance loads. Outputs are one pair of heavy-duty, gold-plated binding posts. A remote trigger input works with 3.3 - 24 V DC at 5 mA or greater. Each chassis measures 191 x 450 x 495 mm (H x W x D) and weighs 29.5 kg.

Engineering and use context

An 850 VA low-noise toroidal transformer, custom-made for Cary, has separate windings for the regulated input board. Power supply capacitance exceeds 98,000 µF per channel. These capacitors are mounted on the amplifier boards, bypass capacitors sit at the output devices themselves, and Cary uses multiple smaller capacitors instead of large ones with their higher ESR. Sixteen high-current 150 W bipolar output devices make up the output stage, cooled by a new heat sink with a larger radiating surface and fin structure. Heat dissipating capability is up to 50% higher than in previous Cary designs.

In the input stage a monolithic device is attached to a custom heat sink for low distortion, low offset voltage and temperature stability. High-precision metal film resistors are used in almost all circuitry. All circuitry sits on four easily replaceable fibreglass printed circuit boards, and a module is replaced after removing the top cover. Protection is thermal and DC-offset, with a high-current relay that disconnects the speakers and no traditional voltage or current limiting. Break-in time is 100 hours. Its chassis is black epoxy-coated steel with a silver anodised aluminium faceplate, and black is optional.

Pairing

Two units are required for a stereo system. A preamplifier with a balanced XLR or single-ended RCA output is required. The black speaker post is the negative leg of a bridged output, not ground, and a subwoofer connects only to the low-level outputs of the preamplifier.

Alternatives

The CAD-211FE is Cary Audio's tube mono power amplifier.

Specifications

  • Model name

    SA-500.1 ES

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    30 000

  • Input impedance (single-ended) (Ω)

    30 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    500

  • Output power (4Ω) (W)

    1000

  • Gain (dBu)

    28

  • Frequency response low +/- 3dB (Hz)

    10

  • Frequency response high +/- 3dB (Hz)

    50 000

  • Signal to Noise Ratio (dB)

    >100

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    0.05

  • Max power consumption (W)

    N/A

  • Damping factor

    >400

  • Dimensions (mm)

    197 × 450 × 495

  • Weight (kg)

    29.5

  • Official link

More components