Hifiverse

Power amplifiers mono — Nagra Reference AMP

Description, images, technical data and specifications

Nagra Reference AMP
Image source - (c) Nagra

The Reference AMP is a monoblock power amplifier from Nagra, the Swiss company founded in 1951 and first known for its portable tape recorders. It has its roots in the HD AMP, originally designed about ten years earlier, and was designed in parallel with the Reference PREAMP. With the Reference DAC, the two form Nagra's Reference line. Nagra products are designed and manufactured by Audio Technology Switzerland.

Key specs that matter

Output is 300 W RMS into 8 ohms, of which 30 W is pure class A, and 1000 W RMS into lower impedances. Bandwidth is 0 Hz - 120 kHz (+0/-0.5 dB), THD+N is below 0.03% and signal-to-noise ratio is typically 110 dB (ASA A-weighted). Inputs are balanced XLR at 88 kohms and unbalanced RCA at 44 kohms, with sensitivity selectable at 1 V or 2 V RMS. Speaker terminals are WBT Next-Gen. Consumption is 1200 W maximum and below 1 W in standby and Auto mode. Each unit measures 23.8 x 64.4 x 54.2 cm (W x H x D) and weighs 56 kg.

Engineering and use context

Its power supply is 25% larger than that of the HD AMP and uses new uprated 2000 VA transformers isolated in epoxy potting. A new input circuit has a very low output impedance to drive the amplifier circuit, and the class A range of operation has been increased. Internal three-stage mechanical damping reduces vibration of key parts. New adjustable resonance decoupling feet combine phenolic material and pure copper, and inner line and speaker cables come from a high-end cable manufacturer.

Two damping factor controlled outputs are provided, A for deeper bass and B for tight bass. A toggle switch cuts DC from incoming signals, and thermal protection trips above +70 °C. Output level is shown on the Nagra modulometer, alongside a clipping LED, and display intensity is adjustable from off to full bright. Trigger jacks in and out (3.5 mm) switch the amplifier on or off from a Nagra MPS or a home automation system. Mains is connected through an IEC C19 inlet for a 20 A plug, and operating ranges are 90 - 110 V, 110 - 132 V or 180 - 264 V AC (50 - 60 Hz). Casework follows the Reference line design, with Nagra's hallmark chamfering and a Reference medallion on the front panel.

Pairing

The matching preamplifier is the Nagra Reference PREAMP. A preamplifier with balanced XLR or unbalanced RCA outputs is required. Output A or B is selected to suit the loudspeaker.

Alternatives

The HD AMP is the earlier Nagra monoblock on which the Reference AMP is based.

Specifications

  • Model name

    Reference AMP

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    N/A

  • Output power (4Ω) (W)

    N/A

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    N/A

  • Signal to Noise Ratio (dB)

    N/A

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    N/A

  • Max power consumption (W)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    N/A

  • Weight (kg)

    N/A

  • Official link

Related content