Hifiverse

Power amplifiers mono - AVM Ovation MA 8.3

Description, images, technical data and specifications

AVM Ovation MA 8.3
Image source - (c) AVM

The Ovation MA 8.3 is a reference mono power amplifier from AVM Audio Video Manufaktur, sold as a pair. Each unit is handcrafted at the AVM facility in Malsch, Germany, and goes through quality checks and a multi-day burn-in process. The aluminium housing is offered in silver or black, optionally with a chrome front, and a clear glass top shows the internal construction.

Key specs that matter

Output is above 600 W into 8 ohms, above 1100 W into 4 ohms and above 1800 W into 2 ohms. Amplification factor is 30 (29.5 dB). Input sensitivity is 2.1 V for 1000 W into 4 ohms, with 20 kohms at the RCA input and 40 kohms at the XLR input. Frequency response and power bandwidth (25 W/4 ohms) are both 5 Hz - above 35 kHz (-3 dB). At 25 W into 4 ohms, distortion is below 0.02%, intermodulation below 0.01% and signal-to-noise ratio above 94 dB(A). Rise time is 10 µs into 4 ohms, slew rate is above 15 V/µs, and damping factor is above 400 at 8 ohms. Power supply is 230 V/50 Hz with 3500 W maximum, 120 W without signal and below 0.5 W in standby. Each unit measures 420 x 432 x 253 mm (L x W x H) and weighs 42 kg.

Engineering and use context

AVM specifies class A/AB MOS-FET high current technology in a symmetrical, DC-coupled architecture, together with a tube stage from its Ovation line. Each channel has 24 MOS-FETs and two 1000 VA toroidal transformers. Input stages are symmetrical, and signal paths are ultra-short.

On the rear panel are one RCA and one XLR input, usable alternatively, the speaker terminals, a mains switch, a 3.5 mm trigger input, an RS-232 serial port and a configuration port. The XLR input has pin 2 as the non-inverting input. Trigger signals from +5 V to +20 V switch the amplifier on and off together with the preamplifier. With a compatible AVM preamplifier such as the Ovation PA 8.2, AIR Trigger (AVM Intelligent Remote) sends the switch-on and switch-off signals inaudibly over the audio cable, and no separate trigger connection is needed. Firmware is updated through the configuration port with a special AVM update dongle.

At start-up the amplifier performs a self-test before it switches to standby. If the display shows INTERNAL FAILURE or DC on input, it switches off. Depending on loudspeaker and output, the amplifier draws up to 16 A from the mains, and the supplied cord has an IEC-60320 C19 connector rated for 16 A.

Pairing

A preamplifier with XLR or RCA outputs is required. Each amplifier requires its own wall socket, not a power distribution strip.

Alternatives

The Ovation MA 6.3 is another AVM mono power amplifier in the Ovation range.

Specifications

  • Model name

    Ovation MA 8.3

  • Input sensitivity (mV)

    2100

  • Input impedance (balanced) (Ω)

    40 000

  • Input impedance (single-ended) (Ω)

    20 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    600

  • Output power (4Ω) (W)

    1100

  • Gain (dBu)

    30

  • Frequency response low +/- 3dB (Hz)

    5

  • Frequency response high +/- 3dB (Hz)

    35 000

  • Signal to Noise Ratio (dB)

    >94

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    < 0.02

  • Max power consumption (W)

    N/A

  • Damping factor

    >400

  • Dimensions (mm)

    420 x 432 x 253

  • Weight (kg)

    42

  • Official link

More components