Hifiverse

Power amplifiers mono — Rotel Michi M8

Description, images, technical data and specifications

Rotel Michi M8
Image source - (c) Rotel

The Michi M8 is a monoblock power amplifier from Rotel's Michi line, which also includes the S5 stereo power amplifier, the P5 preamplifier and the X-series integrated amplifiers. One chassis drives one loudspeaker, so a stereo system needs a pair. It is a class AB design with a balanced circuit and is finished in black.

Key specs that matter

Continuous power output is 1,080 W into 8 ohms and 1,800 W into 4 ohms, with 1,170 W into 8 ohms quoted under the FTC rule. Minimum speaker impedance is 4 ohms. THD is below 0.018%, and IMD (60 Hz - 7 kHz, 4 to 1) is below 0.03%. Frequency response is 20 Hz - 20 kHz (+0 dB, -0.15 dB) and 10 Hz - 100 kHz (+0 dB, -0.5 dB). S/N ratio is 120 dB (IHF A-weighted), and damping factor is 200 (1 kHz, 8 ohms). Input sensitivity and impedance are 3 V and 100 kohms on the balanced XLR input and 1.85 V and 12.5 kohms on the RCA input, with gain of 30 dB and 34 dB respectively. Dimensions are 485 x 238 x 465 mm (W x H x D), front panel height is 220 mm, and net weight is 59.1 kg. Power consumption is 1,200 W, and standby consumption is below 0.5 W, or below 2 W with network wakeup.

Engineering and use context

Michi powers the M8 with a pair of low-noise toroidal transformers, custom engineered and manufactured in-house. They are backed by four British-patented slit-foil bulk storage capacitors with low ESR. Its output stage uses an array of 32 high current output transistors, and according to Michi this reduces the load on individual components. Critical components were also acoustically tuned during development.

Thermal and over-current protection circuits monitor the temperature of the output devices and the current through them. These circuits are independent of the audio signal and shut the amplifier down if operating limits are exceeded, with the front panel Power LED turning red. A high-resolution display on the front panel shows a peak power meter or a spectrum analyser.

On the rear panel are XLR and RCA inputs, two sets of custom Michi speaker binding posts, RS232 and Ethernet connections and 12 V trigger IN and OUT jacks for 3.5 mm plugs. The trigger input accepts AC or DC control signals from 3 V to 30 V. An RR-RH6 remote control is supplied.

Pairing

Loudspeakers rated at 4 ohms or higher are required. Its two sets of binding posts allow single-wire or bi-wire connection. The matching preamplifier is the Michi P5, connected over XLR.

Alternatives

Rotel has no other mono power amplifier in its current Michi or Rotel range.

Specifications

  • Model name

    Michi M8

  • Input sensitivity (mV)

    3000 (XLR) + 1850 (RCA)

  • Input impedance (balanced) (Ω)

    100 000

  • Input impedance (single-ended) (Ω)

    12 500

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    1080

  • Output power (4Ω) (W)

    1800

  • Gain (dBu)

    30 (XLR) + 34 (RCA)

  • Frequency response low +/- 3dB (Hz)

    20

  • Frequency response high +/- 3dB (Hz)

    20 000

  • Signal to Noise Ratio (dB)

    120

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    <0.018

  • Max power consumption (W)

    N/A

  • Damping factor

    200

  • Dimensions (mm)

    485 × 238 × 465

  • Weight (kg)

    59.1

  • Official link