Hifiverse

Power amplifiers mono - McIntosh MC611

Description, images, technical data and specifications

McIntosh MC611
Image source - (c) McIntosh

The MC611 is a one-channel solid-state power amplifier from McIntosh Laboratory, rated at 600 W into 2, 4 or 8 ohms through its output Autoformer. McIntosh intends it for two-channel systems as a pair and for home theatre channels. Compared with the previous 600 W McIntosh monoblock, filter capacity is doubled and dynamic headroom rises from 1.8 dB to 2.8 dB, which the company quotes as a 55% increase. Heavier-gauge internal wiring and upgraded circuit components are also used. The warranty is 3 years.

Key specs that matter

THD is 0.005% maximum at any level from 250 mW to rated power over 20 Hz - 20 kHz, and intermodulation distortion is also 0.005%. Frequency response is +0/-0.25 dB from 20 Hz to 20 kHz and +0/-3 dB from 10 Hz to 100 kHz. Signal-to-noise ratio (A-weighted) is 124 dB balanced and 120 dB unbalanced, and the wideband damping factor exceeds 40. Input sensitivity for rated output is 4.8 V balanced and 2.4 V unbalanced, with 22 kohm input impedance. Voltage gain is 29 dB (8 ohms), 26 dB (4 ohms) and 23 dB (2 ohms). Peak output current is 90 A. Dimensions are 444.5 x 239.7 x 558.8 mm (W x H x D), and weight is 44.32 kg.

Engineering and use context

In its Quad Balanced circuit the MC611 is fully balanced from input to output, with two matched power amplifiers operating in push-pull and their outputs combined in a McIntosh Autoformer. That Autoformer also provides DC protection for the loudspeaker. ThermalTrak output transistors are used, and McIntosh specifies them for lower distortion and cool operation.

Behind the front panel, the audio Autoformer and the power transformer sit in glass-topped enclosures, followed by two Monogrammed Heatsinks. This transformer is potted, weighs 12.7 kg and supplies over 13 A, while four main filter capacitors store over 300 joules.

Power Guard is a waveform comparator of input and output signals and holds THD below 2% with up to a 14 dB overdrive signal. Sentry Monitor disengages the output stage without fuses, and thermal protection mutes the audio on overheating. A 203 mm blue watt meter with Peak Watt Hold mode and direct LED backlighting is on the front panel. Three sets of Solid Cinch binding posts, one per impedance, are spaced wider apart than before. After about 30 minutes without an input signal the amplifier enters standby. Each unit is factory configured for one mains voltage between 100 and 240 V.

Pairing

The speaker cable connects to the tap matching the speaker impedance. Balanced and unbalanced outputs allow bi-amping, tri-amping or a powered subwoofer. The 12 V power control outputs switch it with other McIntosh components.

Alternatives

The McIntosh MC1.25KW is a one-channel solid-state amplifier rated at 1,200 W with Quad Balanced circuitry and an Autoformer.

Specifications

  • Model name

    MC611

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    600

  • Output power (4Ω) (W)

    600

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    10

  • Frequency response high +/- 3dB (Hz)

    100 000

  • Signal to Noise Ratio (dB)

    124

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    0.005

  • Max power consumption (W)

    N/A

  • Damping factor

    >40

  • Dimensions (mm)

    444.5 × 239.7 × 558.8

  • Weight (kg)

    44.3

  • Official link

More components