Hifiverse

Power amplifiers mono — ModWright Instruments KWA 99

Description, images, technical data and specifications

ModWright Instruments KWA 99
Image source - (c) ModWright Instruments

The KWA 99 is a solid-state MOSFET monoblock power amplifier from ModWright Instruments of Amboy, Washington, hand crafted in the USA. ModWright announced it in full production on 19 June 2023 and showed it at Pacific Audio Fest 2023 in SeaTac. Designer Dan Wright chose monoblocks for the compact footprint of the 9 series, which also includes the PH 9.0/X/T phono stage, the Analog Bridge and the LS 99 preamplifier. His brief was a 100 W MOSFET amplifier biased as far into class A as possible, without pure class A because of its inefficiency and heat.

Key specs that matter

Output is 100 W into 8 ohms and 200 W into 4 ohms, with 450 W peak in the launch press release. Gain is 26 dB and input impedance is 47 kohms. Frequency response is 10 Hz - 150 kHz (+0, -1 dB). Noise floor is -90 dB (unweighted) and THD is below 0.05%. Each monoblock measures 267 x 165 x 406 mm (W x H x D) including footers and 25 mm binding posts, and weighs 13.6 kg, or 15.9 kg shipped. Versions exist for 120 V, 220 V and 220 - 240 V mains.

Engineering and use context

Its output devices are current-production Exicon lateral MOSFETs. Operation is class A/B with a high class A bias, though not pure class A, and the enclosure has fully exposed heatsinks for high-bias, lower-distortion operation. There is zero global feedback. One RCA and one XLR input are transformer coupled to the input stage with a floated ground, and the same transformer coupling provides DC input protection.

Internal thermal overload protectors cut all power on overheating. Short-circuit and over-current protection is ModWright's proprietary TSP (Total Silent Protection) circuit, which resides outside the signal path and mutes the affected channel. All fuses are internal and are replaced only at the factory.

Each chassis has one pair of 5-way binding posts, red positive and black negative, and is not bridgeable. On the front panel are amber-illuminated power VU meters with a dimmer knob that goes down to off. At switch-on, blue internal LEDs flash for about 45 seconds while the amplifier warms up and stabilises, and a rear LED ON/LED OFF switch disables them. A 12 V trigger mini-jack input switches the amplifier on and off. ModWright gives a 5-year warranty from the date of purchase.

Pairing

A preamplifier with RCA or XLR outputs is required. The matching preamplifier is the ModWright LS 99, linked through the 12 V trigger. ModWright has tested the KWA 99 into 2 ohm loads, and a lower impedance engages the over-current muting.

Alternatives

The Ambrose A30 is a discontinued ModWright tube monoblock with three EL34 output tubes in single-ended parallel and a 12AT7 driver, rated at 32 W in class A into 6 ohms.

Specifications

  • Model name

    KWA 99

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    100

  • Output power (4Ω) (W)

    200

  • Gain (dBu)

    26

  • Frequency response low +/- 3dB (Hz)

    10

  • Frequency response high +/- 3dB (Hz)

    150 000

  • Signal to Noise Ratio (dB)

    -90

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    <0.05

  • Max power consumption (W)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    254 x 152 x 381

  • Weight (kg)

    13

  • Official link