Hifiverse

Power amplifiers mono - Fluo DM250

Description, images, technical data and specifications

Fluo DM250
Image source - (c) Fluo

The DM250 is a two-channel power amplifier from FLUO (Fast Linear Ultimate Operation), a Winchester, England, company led by Keith Martin, the founder of IsoTek. It is a true dual mono design, with two mono block amplifiers for the left and right channels in one chassis, and it sits between the DM125 and the M500 monoblocks in the range.

Key specs that matter

Output power is 250 W into 8 ohms and 500 W into 4 ohms (resistive load). Into 2 ohms it is 1,000 W short-term, reduced to about 900 W by the required mains fuse. Each channel has a 6.3 A slow-blow mains fuse that limits long-term consumption to 1,450 W. Idle consumption is 100 W, with all data based on 230 V AC mains. Inputs are a balanced 3-pin XLR at 40 kOhm (pin 2 plus, pin 3 minus, pin 1 ground) and an unbalanced RCA at 20 kOhm. Dimensions are 485 x 270 x 535 mm (W x H x D).

Engineering and use context

Two mains inlets with two power cords supply two separate mains transformers, so a high power demand on the right channel does not affect the left, and vice versa. According to FLUO, this brings the DM250 closer to the performance of the M500. Each channel uses a Single Die MOSFET in the output stage, rated by FLUO at 388 A peak current and around 450 W. Into a 2 ohm load the circuit needs no more than 38 A, so the transistor operates within the first 10% of its current range, where it is more linear. Its internal resistance goes down to 0.022 ohm.

In the power supply, current leaves the PCB through 2.5 sq mm internal wiring, returns to the board and runs by wire again to the output relays and beyond them. A 105 µm PCB track would need to be about 25 mm wide to match this wiring, and the method adds hand assembly time. Supply capacitors have a very low internal resistance, even at 100 kHz. The working range is 16 Hz to beyond 20 kHz, and signals at 200 kHz and 201 kHz are removed, since together they can produce a 1 kHz tone.

A protection system checks for abnormal high frequencies, voltage, current, phase angle and load. On a fault it mutes the input for 1 second, tests again for 1 ms and restarts automatically once the fault is gone. Loads below 1.5 ohms are not accepted, and the audio is muted if operating temperatures exceed the limit. The chassis shape, heat sink fins and top panel are designed to diffuse sound waves and lower resonance frequencies.

Pairing

The matching preamplifier is the FLUO PRE1, which uses the same JFET balanced input circuit and has 75 ohm RCA and 150 ohm XLR outputs. FLUO recommends shielded signal cables only.

Alternatives

The FLUO DM125 is the smaller dual mono stereo power amplifier, rated at 125 W into 8 ohms, with separate capacitors, rectifiers and transformer windings per channel.

Specifications

  • Model name

    DM250

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    40 000

  • Input impedance (single-ended) (Ω)

    20 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    250

  • Output power (4Ω) (W)

    500

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    N/A

  • Signal to Noise Ratio (dB)

    N/A

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    N/A

  • Max power consumption (W)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    485 x 270 x 535

  • Weight (kg)

    N/A

  • Official link

More components