Hifiverse

Power amplifiers mono - Kora CSA 1150

Description, images, technical data and specifications

Kora CSA 1150
Image source - (c) Kora

The CSA 1150 is a pure Class A mono power amplifier from Kora of Portet-sur-Garonne near Toulouse. François Philibert founded Kora in Toulouse in 1990, the company stopped trading in the early 2000s, and Bruno Vander Elst revived the name in 2017. The CSA series has four versions, small or large, mono or stereo, and the CSA 1150 is the small mono model. It was first shown with the other three at the Munich show in May 2025, priced at EUR 19,800 per unit.

Key specs that matter

Output power is 1 x 150 W into 8 ohms in pure Class A. A linear power supply with 400,000 µF of filtering powers the amplifier. Inputs are one RCA (unbalanced, 47 kohms) and one XLR (balanced, 20 kohms), selected by a switch on the rear panel. Its aluminium and steel case in Mineral grey measures 420 x 440 x 260 mm and weighs 32 kg. A power cord, the user manual and a general information booklet are included.

Engineering and use context

Like every Kora amplifier, the CSA 1150 is powered by Square Tube and is a hybrid that combines tubes with audio transistors. Its output stage is a pure Class A transistor stage, with the signal taken from the collector and the transistors biased in the middle of their characteristics, so crossover distortion is pushed back to the point of clipping. Kora quotes 40 output transistors for the small versions and 60 for the large ones, and states stability on complex, highly capacitive loads. This output stage is designed as a current source. Between the Square Tube and the power section sits a voltage/current converter made only of precision resistors, without semiconductors.

Two bias modes are available - nominal current for full power and an economical mode with the current reduced by half. A rear CURRENT switch selects LOW, AUTO or HIGH, and in AUTO the amplifier changes to high current when the signal requires it and returns to low current in about ten seconds. With the POWER switch on AUTO, a modulation detector turns the unit on when a signal reaches the RCA or XLR input and returns it to standby after more than one minute of silence. The rear panel also carries a GAIN potentiometer for input sensitivity and a PHASE switch (0° or 180°). At power-up the filter capacitors pre-charge slowly over a few minutes. A rear indicator checks mains polarity. On the front are a screen and a single rotary push button, and the speaker terminals accept 4 mm banana plugs or bare wire.

Pairing

A preamplifier is required, and the matching Kora preamplifier is the PR140. Two units are needed for stereo. The GAIN and PHASE controls allow use in multi-amplified systems.

Alternatives

The Kora CSA 1200 is the large mono model, with 1 x 200 W into 8 ohms, 560,000 µF of filtering, a 420 x 660 x 260 mm case and a weight of 45 kg.

Specifications

  • Model name

    CSA 1150

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    150

  • Output power (4Ω) (W)

    N/A

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    N/A

  • Signal to Noise Ratio (dB)

    N/A

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    N/A

  • Max power consumption (W)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    420 x 440 x 260

  • Weight (kg)

    32

  • Official link

More components