Hifiverse

Integrated amplifiers — Anthem STR Integrated Amplifier

Description, images, technical data and specifications

Anthem STR Integrated Amplifier
Image source - (c) Anthem

The STR Integrated Amplifier is the one-box model of Anthem's STR series and is made in Canada. Anthem presents it as a new platform of power and control that combines a stereo power amplifier, a preamplifier, a DAC, MM and MC phono inputs and bass management for two subwoofers. It arrived in 2018 at USD 4,499, alongside the STR Preamplifier at USD 3,999 and the STR Power Amplifier at USD 5,999. Finishes are Black or Silver, and the warranty is five years on parts and labour.

Key specs that matter

Continuous output is 200 W into 8 ohms, 400 W into 4 ohms and 550 W per channel into 2 ohms. Analogue inputs are four single-ended RCA pairs, one balanced XLR pair and separate MM and MC phono inputs. Digital inputs are two S/PDIF coaxial, two optical, one balanced AES/EBU and one asynchronous USB. Via USB it accepts PCM up to 32-bit/384 kHz and DSD 2.8/5.6 MHz. Dimensions are 432 x 172 x 445 mm (W x H x D), and weight is 18 kg.

Engineering and use context

Each channel has eight bipolar output devices. They are powered by a toroidal transformer supply, and Anthem specifies that the transformer is engineered in-house. Advanced Load Monitoring is proprietary, non-invasive circuitry that protects the output section.

In the preamplifier Anthem uses the shortest possible signal paths and differential circuitry, with a design target of low noise and distortion. Lower-resolution digital sources are up-sampled to 24-bit/192 kHz. Analog Direct mode bypasses all digital processing for analogue inputs. Its phono section is dedicated and shielded, with separate inputs for moving magnet and moving coil cartridges.

Bass management covers two subwoofers in either mono or stereo configuration. Setup and adjustments run through a high-resolution graphic display on the front panel. Control is possible via Ethernet or RS-232, and an IR remote is supplied.

Pairing

The 2 ohm rating allows loudspeakers with low impedance. A turntable with an MM or MC cartridge connects directly to the phono inputs. One or two active subwoofers connect to the subwoofer outputs.

Alternatives

The discontinued Anthem Integrated 225, rated at 225 W per channel into 8 ohms, was the brand's earlier integrated amplifier with a built-in phono stage.

Specifications

  • Model name

    STR Integrated Amplifier

  • Type

    Integrated Amplifier with DAC and Phono

  • Analog inputs (balanced)

    1

  • Analog inputs (single-ended)

    4 + 2 (Phono)

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • D/A conversion

    Yes

  • Phono MM/MC current-sensing input impedance (Ω)

    100 (MC), 47 000 (MM)

  • Output power (8Ω) (W)

    200

  • Output power (4Ω) (W)

    400

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    10

  • Frequency response high +/- 3dB (Hz)

    80 000

  • Signal to Noise Ratio (dB)

    112

  • Total Harmonic Distortion + Noise (%)

    0.0008

  • Damping factor

    N/A

  • Dimensions (mm)

    172 × 432 × 445

  • Weight (kg)

    18

  • Official link

Related content