Hifiverse

Integrated amplifiers — T+A PA 2500 R

Description, images, technical data and specifications

T+A PA 2500 R
Image source - (c) T+A

The PA 2500 R is the larger of the two integrated amplifiers in T+A's R-Series. T+A describes it as twice as tall as the PA 2000 R. The basic circuit and even the circuit board layouts are identical to those of the smaller model, while the heat-sinks are twice the size and the case holds two mains power supply units. Like the rest of the series, it is designed and built by T+A elektroakustik in Herford, Germany.

Key specs that matter

Rated output per channel is 140 W into 8 ohms, 280 W into 4 ohms and 560 W into 2 ohms. Power stage frequency response is 1 Hz - 150 kHz (+0/-3 dB), slew rate is 60 V/µs, damping factor is above 65, and reservoir capacity is 120,000 µF. Its preamplifier stage covers 0.5 Hz - 300 kHz (+0/-3 dB), with a signal-to-noise ratio of 105 dB unweighted and 109 dB A-weighted and channel separation above 90 dB. Inputs are four RCA (250 mV - 4 V, 20 kohms) and three balanced XLR (500 mV - 8 V, 5 kohms). Pre-outs are RCA (1 V nominal, 9.5 V max., 75 ohms) and XLR (1.45 V nominal, 19.6 V max., 75 ohms), and the headphone output is 50 ohms. Dimensions are 165 x 460 x 405 mm (H x W x D), and weight is 14.5 kg.

Engineering and use context

Each power supply is a regulated high-frequency sine-wave mains supply with generous reservoir capacity, rated by T+A at up to 1200 W. A protective circuit sits outside the signal path. It compares the signal before the output stage with the output signal and switches off the output relays on clipping or distortion, overheating or a short circuit.

Parts include low-loss mica capacitors with silver electrodes, zero-induction resistors and nickel-free gold- or rhodium-plated terminals. Bass and treble controls are switchable and channel-separate (-6 to +8 dB), and loudness is switchable and variable. An optional MM or MC phono module replaces one high-level input, with 16 capacitance or 16 impedance settings. Input 3 (XLR) or input 5 (RCA) can be configured as a surround pass-through, and a trigger input accepts 5 - 20 V.

Control electronics are recessed into the solid aluminium front profile behind a dimmable VFD. Control is via the R2-Link system bus and the SRC 1 remote, and with an MP 2000 R in the system the T+A App can be used. Finishes are silver or black anodised aluminium.

Pairing

Power ratings extend to loudspeaker loads of 2 ohms. The matching sources in the R-Series are the MP 2000 R G3 and MP 2500 R G3 multi source players.

Alternatives

The PA 2000 R is the lower-profile R-Series integrated amplifier with the same basic circuit.

Specifications

  • Model name

    PA 2500 R

  • Type

    Integrated Amplifier

  • Analog inputs (balanced)

    N/A

  • Analog inputs (single-ended)

    3

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • D/A conversion

    N/A

  • Phono MM/MC current-sensing input impedance (Ω)

    N/A

  • Output power (8Ω) (W)

    N/A

  • Output power (4Ω) (W)

    N/A

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    0.5

  • Frequency response high +/- 3dB (Hz)

    300 000

  • Signal to Noise Ratio (dB)

    105 / 109

  • Total Harmonic Distortion + Noise (%)

    < 0,001

  • Damping factor

    N/A

  • Dimensions (mm)

    165 × 460 × 405

  • Weight (kg)

    14.5

  • Official link

More components