Hifiverse

Integrated amplifiers - VTL IT-85

Description, images, technical data and specifications

VTL IT-85
Image source - (c) VTL

The IT-85 is a tube integrated amplifier from VTL (Vacuum Tube Logic) of Chino, California, and the only integrated model in the VTL range. It is a full line stage preamplifier and power amplifier in one chassis, with a fully active, pure tube line stage. Its power section uses power supply components and output and power transformers from the VTL ST-85 stereo amplifier.

Key specs that matter

Output power is 60 W per channel into 5 ohms (20 Hz - 20 kHz, <3% THD), in class AB1. The tube complement is 4 x EL34, 4 x 12AT7 and 2 x 12AU7. Small-signal frequency response is 0 - 60 kHz (<0.2% THD at 1 W). Inputs are five pairs of single-ended RCA plus a Proc/Amp input, and outputs are one pair of 5-way binding posts, Pre Out, Tape Out and a headphone output. Input sensitivity and impedance are 180 mV and 20 kohms at the line inputs, 575 mV and 135 kohms at the amp input. Output impedance is 1.55 ohms at the speaker terminals, 16 ohms at the headphone output and 400 ohms at the pre out. Load settings are 5 ohms for loudspeakers and 50 - 500 ohms for headphones. Power consumption is 200 W at idle and 600 W at full power. Dimensions are 40 x 28 x 17.75 cm (W x D x H), and shipping weight is 29.5 kg.

Engineering and use context

VTL equips the line stage with a regulated B+ supply and a buffered pre out that can drive a subwoofer. A pair of processor loop inputs connects directly to the amplifier section, next to a pair of tape outputs. Volume and mute are remote controlled, with automatic mute at power up and power down.

Its headphone section is driven off the tube output stage and output transformer of the power amplifier. A front panel selector switches between headphones and loudspeakers, the pre out mutes when headphones are plugged in, and the headphone circuit shuts down automatically with no load. Individual bias measurement and adjustment points for each output tube are on the top deck.

An extruded, machined aluminium front panel comes in silver as standard or in black, and a protective cage is supplied. The chassis has an angled back for access to inputs and outputs, a detachable IEC power cord and gold-plated VTL binding posts and RCA jacks. Each unit is hand-built in the VTL factory in California.

Pairing

The pre out is gain-matched to the VTL ST-85, and the pair allows horizontal bi-amping. Loudspeakers with bi-wire terminals are required for that setup.

Alternatives

VTL offers no other integrated amplifier, so the IT-85 has no in-brand alternative in this category.

Specifications

  • Model name

    IT-85

  • Type

    N/A

  • Analog inputs (balanced)

    N/A

  • Analog inputs (single-ended)

    5

  • Input sensitivity (mV)

    180

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    20 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • D/A conversion

    N/A

  • Phono MM/MC current-sensing input impedance (Ω)

    N/A

  • Output power (8Ω) (W)

    60

  • Output power (4Ω) (W)

    N/A

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    20

  • Frequency response high +/- 3dB (Hz)

    20 000

  • Signal to Noise Ratio (dB)

    N/A

  • Total Harmonic Distortion + Noise (%)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    400 x 280 x 177.5

  • Weight (kg)

    29.5

  • Official link