Hifiverse

Integrated amplifiers — CH Precision I1

Description, images, technical data and specifications

CH Precision I1
Image source - (c) CH Precision

The I1 Universal Integrated Amplifier is the stereo integrated amplifier of CH Precision, the Swiss maker otherwise known for multi-chassis separates. CH Precision describes it as a combination of the C1 DAC/Controller and the A1 power amplifier, with elements taken from the L1 line stage and P1 phono stage. Its pricing at the US launch ran from USD 38,000 to 52,000, depending on the options installed.

Key specs that matter

Output power is 2 x 100 W RMS into 8 ohms and 2 x 175 W RMS into 4 ohms (1 kHz). Analogue inputs are one XLR and two RCA per channel, with input impedance of 94 kohms or 600 ohms balanced and 47 kohms or 300 ohms single-ended, and maximum levels of 8 V RMS and 4 V RMS. Each digital input board carries CH-Link HD, AES/EBU, S/PDIF (RCA) and TOSLINK. CH-Link HD accepts PCM 44.1 - 768 kHz and DSD 2.8224 - 22.5792 MHz, AES/EBU and S/PDIF accept PCM up to 192 kHz and DSD 2.8224 MHz in DoP. THD+N is below 0.0025%, signal-to-noise ratio is above 125 dB and dynamic range is above 120 dB (20 Hz - 20 kHz, A-weighted). Dimensions are 440 x 440 x 133 mm (W x D x H), and weight is 33 kg. Power consumption is 120 W at idle and 1000 W maximum.

Engineering and use context

Analogue inputs are converted to DXD at 24 bit/384 kHz, one A/D converter per channel. Conversion uses one multi-bit delta-sigma converter per channel with the proprietary PEtER upsampling filter, a short, low-ringing, time-optimised, synchronous 32-bit fixed-point algorithm, and full MQA decoding is included. The output stage is fully discrete, dual-mono and symmetrical, and it is powered by a 1000 VA transformer with 100,000 µF of reservoir capacitance. Every stage has its own shunt-regulated supply. Nominal gain is +24 dB, with a volume range from -96 dB to +24 dB.

Two expansion slots take a USB audio input (PCM to 384 kHz, DSD to 5.6448 MHz in DoP), a second digital input board or a Clock-Sync module. An Ethernet streaming board replaces the network control board without using a slot and supports UPnP/DLNA, Roon Ready, Qobuz Connect and Tidal Connect. An optional circuit block turns the RCA inputs into current-sensing MC phono inputs below 100 milliohms at virtual ground, with RIAA, eRIAA, Decca, Columbia, EMI and Teldec curves held to ±0.01 dB. Controls are an 800 x 480 AMOLED display, a dual concentric encoder, an IR remote and an Android app.

Pairing

The XLR preamplifier output (4 V RMS max) allows an additional power amplifier for bi-amping. In pure analogue power amp mode an external DAC or preamplifier is connected upstream. The CH-Link HD input matches the D1.5 and D10 transports.

Alternatives

The I1 is the only integrated amplifier in the CH Precision range, where all other amplification comes as separate preamplifiers and power amplifiers.

Specifications

  • Model name

    I1

  • Type

    Integrated amplifier (phono, USB, and streaming — optional boards)

  • Analog inputs (balanced)

    1

  • Analog inputs (single-ended)

    2

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    94 000 or 600

  • Input impedance (single-ended) (Ω)

    47 000 or 300

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • D/A conversion

    N/A

  • Phono MM/MC current-sensing input impedance (Ω)

    N/A

  • Output power (8Ω) (W)

    2x 100

  • Output power (4Ω) (W)

    2x 175

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    N/A

  • Signal to Noise Ratio (dB)

    N/A

  • Total Harmonic Distortion + Noise (%)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    440 x 440 x 133

  • Weight (kg)

    33

  • Official link