Hifiverse

Integrated amplifiers — Copland CSA70

Description, images, technical data and specifications

Copland CSA70
Image source - (c) Copland

The CSA70 is an integrated amplifier with a built-in DAC, MM phono stage and headphone amplifier from Copland, made in Denmark. Unlike the larger CSA100 and CSA150, it does not use tubes in the line stage, and its preamplifier section is solid-state. The power amplifier uses the same technology as the CSA100 and CSA150. A remote control is supplied, and Copland gives a three-year warranty to the first purchaser.

Key specs that matter

Output power is 2 x 70 W into 8 ohms, with a minimum load of 2 ohms. Analogue inputs are one MM phono and three unbalanced line inputs on RCA. Digital inputs are one coaxial S/PDIF, two optical S/PDIF and one USB, with aptX HD Bluetooth as an optional extra. Outputs are a fixed unbalanced line out, a variable unbalanced pre-out and a front 6.3 mm headphone socket. Line input impedance is 50 kohms at 200 mV sensitivity, and the phono input has 47 kohms, 200 pF and 2.6 mV sensitivity. Frequency response is 10 Hz - 200 kHz (-3 dB), THD is better than 0.01% and signal-to-noise ratio is better than 90 dB (IHF-A). Phase is non-inverting. Maximum power consumption is 400 W. Dimensions are 435 x 135 x 370 mm (W x H x D), and shipping weight is 13 kg.

Engineering and use context

Copland describes the power amplifier as having a feedback structure inherently faster than conventional amplifiers, with a wide large-signal frequency response. It is designed for awkward dynamic loads presented by loudspeakers.

USB playback runs through an asynchronous converter module, a modified version of the Amanero module, with its own power supply and its own power transformer secondary winding. It accepts 16- to 24-bit files at sampling rates up to 192 kHz. Front-panel LEDs show when a digital source is locked and when the incoming sampling rate is 96 kHz or higher. The coaxial input carries S/PDIF as a single-ended square wave of around 0.5 V peak-to-peak.

The CSA70 is prepared for a future HD Bluetooth module, and the rear panel already has an SMA antenna connector and a reset button for it. A ground terminal sits next to the phono input. At switch-on the amplifier goes through a 15-second start-up procedure, indicated by a flashing lamp. The headphone amplifier has an output impedance of 40 ohms, THD better than 0.01% and a frequency response of 10 Hz - 150 kHz (-3 dB).

Pairing

The phono input requires a moving-magnet cartridge. A separate power amplifier connects to the variable pre-out. A Windows computer needs the Amanero driver for USB playback, while macOS and Linux work without one.

Alternatives

The CSA100 is the next Copland integrated amplifier, with tubes in its line stage.

Specifications

  • Model name

    CSA70

  • Type

    Integrated Amplifier with DAC and Phono

  • Analog inputs (balanced)

    N/A

  • Analog inputs (single-ended)

    3 + 1 (Phono)

  • Input sensitivity (mV)

    200

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    50 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • D/A conversion

    Yes

  • Phono MM/MC current-sensing input impedance (Ω)

    47 000

  • Output power (8Ω) (W)

    N/A

  • Output power (4Ω) (W)

    N/A

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    10

  • Frequency response high +/- 3dB (Hz)

    200 000

  • Signal to Noise Ratio (dB)

    90

  • Total Harmonic Distortion + Noise (%)

    0.01

  • Damping factor

    N/A

  • Dimensions (mm)

    435 x 135 x 370

  • Weight (kg)

    13

  • Official link

More components