Hifiverse

Vorverstärker - Octave Audio Jubilee Preamp SE

Beschreibung, Bilder, technische Daten und Spezifikationen

Octave Audio Jubilee Preamp SE
Bildquelle - (c) Octave Audio

The Jubilee Preamp SE is a tube line preamplifier from Octave of Karlsbad, Germany, and the successor to the Jubilee Preamp that Octave first presented in 1998. It is the reference preamplifier of the Jubilee line, with optimised circuitry, a new operating and display concept and an expanded range of functions. Octave designs and manufactures it in Germany.

Key specs that matter

Four 12AU7 Tung Sol (ECC82) tubes make up the tube complement. Inputs are four RCA, two XLR and one home theatre bypass (RCA), and outputs are two RCA, two XLR and one monitor (RCA). Gain is 10 dB / 16 dB (low / high) via RCA and 16 dB / 22 dB via XLR. Frequency range is 3 Hz - 100 kHz (1.5 dB), harmonic distortion is 0.1% at 3 V / 7.5 kOhm, and Octave quotes a signal-to-noise ratio of 100 dB (gain high) / 98 dB (gain low). Output impedance is 33 ohms. The preamplifier measures 445 x 152 x 480 mm (W x H x D) and weighs 17.2 kg, and the external power supply measures 220 x 152 x 480 mm and weighs 11.5 kg.

Engineering and use context

It keeps the tube-based precision balancing stage, the discrete solid-state output stage and the zero-feedback circuit of the Jubilee Preamp. New in-house input transformers on the XLR inputs are designed for DACs with output levels up to 8 V RMS, with an input impedance of 80 kOhm, a frequency range of 5 Hz - 150 kHz and THD+N of 0.005%. No transistor input stage sits in this path. Its circuit boards use a Matsushita board material with 70 µm copper, developed for sensitive analogue circuits. Vishay/Beyschlag film resistors are used in the analogue section, and Epcos electrolytic capacitors made in the EU, with a lifespan of over 20 years, in the power supply. According to Octave, these changes give a higher bandwidth and 3 dB lower noise.

Behind the tube stage sits a discrete semiconductor amplifier, also without negative feedback. Power amplifiers with an input impedance down to 600 ohms can be connected via RCA or XLR, with signal cables up to 8 m long. A vacuum-encapsulated low-noise mains transformer is mounted in the external power supply. The front panel has a volume display with LED indicator (red as standard, other colours on request), and gain, phase and mono are switchable. Device feet are a resonance-optimised three-layer construction. A 47-position stepped attenuator is available as an option.

Pairing

The dual RCA and XLR outputs allow bi-amping, tri-amping or quad-amping. A headphone amplifier with its own volume control connects to the monitor output. Matching power amplifiers of the same line are the Jubilee 300 B and Jubilee Class A.

Alternatives

The Jubilee Preamp is the earlier version, with six RCA inputs, a tape record loop and broadband XLR input transformers.

Spezifikationen

  • Modellbezeichnung

    Jubilee Preamp SE

  • Analogeingänge (symmetrisch)

    2

  • Analogeingänge (unsymmetrisch)

    5

  • Analogausgänge (symmetrisch)

    2

  • Analogausgänge (unsymmetrisch)

    2

  • Verstärkung (dBu)

    10 RCA, 16 XLR

  • Eingangsempfindlichkeit (mV)

    N/A

  • Ausgangsspannung (V)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Ausgangspegel (symmetrisch) (dBu)

    N/A

  • Maximaler Ausgangspegel (unsymmetrisch) (dBu)

    N/A

  • Regelbereich der Lautstärke (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    3

  • Obere Grenzfrequenz +/- 3dB (Hz)

    100 000

  • Signal-Rausch-Abstand (SNR, unbewertet) (dB)

    100

  • Klirrfaktor + Rauschen (THD+N) (%)

    0.1

  • Abmessungen (mm)

    445 x 152 x 480 (Preamp) + 220 x 152 x 480 (PSU)

  • Gewicht (kg)

    17.2 (Preamp) + 11.5 (PSU)

  • Offizieller Link