Hifiverse

Endstufen Stereo - Emotiva XPA-5 Gen3

Beschreibung, Bilder, technische Daten und Spezifikationen

Emotiva XPA-5 Gen3
Bildquelle - (c) Emotiva

The XPA-5 Gen3 is a five-channel power amplifier from Emotiva, built on the fully modular XPA Gen3 platform. It ships with five High-Powered Single Channel Modules installed, and two module slots remain available for later expansion. Emotiva intends it for a 5.1 system or for the five main channels of a 5.1.2, 5.1.4 or 5.1.6 Dolby Atmos or DTS:X setup.

Key specs that matter

Power output with one channel driven is 300 W RMS into 8 ohms (THD <0.1%) and 550 W RMS into 4 ohms (THD <0.2%), from 20 Hz to 20 kHz. With two channels driven it is 300 W into 8 ohms and 490 W into 4 ohms per channel. With all five channels driven the rating is 250 W into 8 ohms and 380 W into 4 ohms per channel, at THD <0.1%. Power bandwidth at rated power is 20 Hz - 20 kHz (±0.1 dB), and broadband frequency response is 5 Hz - 80 kHz (+0/-2 dB). THD+N is <0.005% (100 W RMS, 1 kHz, 8 ohms). Signal-to-noise ratio is >117 dB ref rated power and >91 dB ref 1 W (unbalanced, A-weighted). Damping factor is >500 into 8 ohms, gain is 29 dB and input sensitivity is 1.71 V. Input impedance is 33 kohms balanced and 23.5 kohms unbalanced. Minimum recommended load is 4 ohms per channel, and maximum power consumption is 2,000 W. Dimensions are 432 x 203 x 483 mm (W x H x D, with feet), and weight is 20.9 kg.

Engineering and use context

Every channel uses an independent, fully discrete, dual differential, high current Class A/B amplifier module with a short signal path. An audiophile-grade, high-efficiency switch mode power supply with Emotiva's Optimized Class H power supply topology powers the modules. Microprocessor-controlled fault protection guards against overheating, shorted speaker connections and ground faults, while a resettable circuit breaker on the rear panel provides AC protection. On the front, a blue status LED per channel turns red on a fault, and the standby button has a halo ring that changes colour between standby and on.

Inputs are balanced XLR and unbalanced RCA on each channel, chosen by dedicated metal toggle switches on the rear panel. Speaker outputs are gold-plated 5-way binding posts. Trigger input voltage is 5 - 12 V (AC or DC), and the 12 V DC trigger output can drive loads up to 120 mA. Mains operation is 100 - 250 V AC at 50/60 Hz, detected automatically.

Pairing

An AV processor, a stereo preamplifier or an AV receiver with XLR or RCA preamp outputs is required. In a Dolby Atmos or DTS:X layout, the height channels require a second amplifier or the amplification of the receiver.

Alternatives

The XPA-7 Gen3 is Emotiva's seven-channel amplifier on the same platform, rated at 200 W per channel into 8 ohms with all seven channels driven.

Spezifikationen

  • Modellbezeichnung

    XPA-5 Gen3

  • Eingangsempfindlichkeit (mV)

    1710

  • Eingangsimpedanz (symmetrisch) (Ω)

    33 000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    23 500

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    5 x 250

  • Ausgangsleistung (4Ω) (W)

    550

  • Verstärkung (dBu)

    29

  • Untere Grenzfrequenz +/- 3dB (Hz)

    5

  • Obere Grenzfrequenz +/- 3dB (Hz)

    80 000

  • Signal-Rausch-Abstand (dB)

    >117

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    < 0.005

  • Maximale Leistungsaufnahme (W)

    2000

  • Dämpfungsfaktor

    >500

  • Abmessungen (mm)

    432 x 203 x 483

  • Gewicht (kg)

    20,9

  • Offizieller Link

Weitere Komponenten