Hifiverse

Endstufen Stereo - Emotiva BasX A2L+

Beschreibung, Bilder, technische Daten und Spezifikationen

Emotiva BasX A2L+
Bildquelle - (c) Emotiva

The BasX A2L+ is a two-channel power amplifier in Emotiva's BasX range, announced on 28 February 2025 with a list price of USD 349. Emotiva positions it for powering several separate stereo zones, and for this it has RCA loop outputs and a gain reduction adjustment on the rear panel.

Key specs that matter

Rated output is 50 W RMS per channel into 8 ohms (20 Hz - 20 kHz, THD < 0.1%) and 90 W RMS per channel into 4 ohms (1 kHz, THD < 1%), two channels driven. Power bandwidth is 20 Hz - 20 kHz (±0.07 dB) at rated power, and broad band frequency response is 10 Hz - 80 kHz (+0/-1.8 dB). THD+N is < 0.02% (A-weighted), signal-to-noise ratio is > 112 dB referenced to rated power (A-weighted), and damping factor is > 500 into 8 ohms. Input sensitivity for rated power is 0.70 V into 8 ohms and 0.65 V into 4 ohms. Gain is 29 dB and input impedance is 27 kohms. Minimum recommended load is 4 ohms per channel. It measures 432 x 79 x 318 mm (W x H x D, including feet) and weighs 6.8 kg.

Engineering and use context

Emotiva describes a heavy-duty linear power supply with an oversized toroidal transformer and a high current, short signal path Class A/B output stage. Monitoring and protection circuitry is microprocessor-controlled and covers excessive operating temperature, shorted speaker connections and ground faults. Circuit boards are double-sided FR4 with plated-through holes, and the heavy steel chassis carries a milled aluminium faceplate.

Each channel has one unbalanced RCA input and one RCA loop output, so several A2L+ units can be chained from one source. A rear-panel gain reduction adjustment sets gain anywhere from 18 dB to 29 dB for level matching between zones. For remote switching there is a 5 - 12 V (AC or DC) trigger input and a 12 VDC trigger output rated up to 120 mA. Auto-On switches the amplifier on when an audio signal is detected. Mains of 115 or 230 VAC at 50/60 Hz is detected automatically. On the front are a standby button, an amber standby LED and one blue status LED per channel that turns red on a fault, and a rear switch disables the status LEDs. Speaker outputs are 5-way binding posts.

Pairing

A preamplifier, processor or AV receiver with RCA pre-outs is required. Speakers of 4 ohms or higher per channel are within the rated load, or two 8 ohm speakers in parallel. The loop outputs allow a second A2L+ for another zone.

Alternatives

The BasX A2+ is the higher-powered stereo model in the range, with 160 W per channel into 8 ohms and balanced XLR inputs beside the RCA inputs.

Spezifikationen

  • Modellbezeichnung

    BasX A2L+

  • Eingangsempfindlichkeit (mV)

    1200

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    27 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    50

  • Ausgangsleistung (4Ω) (W)

    90

  • Verstärkung (dBu)

    29

  • Untere Grenzfrequenz +/- 3dB (Hz)

    10

  • Obere Grenzfrequenz +/- 3dB (Hz)

    80 000

  • Signal-Rausch-Abstand (dB)

    >112

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    < 0.02

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    >500

  • Abmessungen (mm)

    432 × 79 × 318

  • Gewicht (kg)

    6,8

  • Offizieller Link

Weitere Komponenten