Hifiverse

Endstufen Mono - Audio Note Quest

Beschreibung, Bilder, technische Daten und Spezifikationen

Audio Note Quest
Bildquelle - (c) Audio Note

The Quest is a mono power amplifier from Audio Note (UK), a pure class A single-ended tube design with a single 300B triode per channel. It fulfils all of Audio Note's Level 3 criteria - pure class A operation, zero negative feedback, a single-ended output stage, tube rectification, directly heated triode operation, and materials and component quality. Six versions are listed - Quest, Quest Silver and Quest Silver Signature, each also available as a Low Gain model.

Key specs that matter

Maximum output is 8 W RMS into 4 or 8 ohm loads. Input impedance is 100 kOhm at line level. Input sensitivity is 160 mV for the standard version and 3.3 V for the Low Gain version. Channel balance is ±0.3 dB. Each chassis carries one 300B, one 5U4G and one 6SN7, with a 6J5 in place of the 6SN7 on the Low Gain version. Each amplifier weighs 20 kg and measures 195 x 205 x 506 mm (H x W x D). Mains input is AC 100-120 V or 220-240 V, 50/60 Hz, and maximum power consumption is 200 W.

Engineering and use context

In the standard Quest the 6SN7 is the input stage tube, the 300B is the output tube and the 5U4G is the rectifier. The Quest Silver adds Audio Note tantalum film resistors, Audio Note copper foil signal capacitors and Audio Note IHiB double C-core output transformers. On the Quest Silver Signature the copper foil signal capacitors and tantalum film resistors are joined by SHiB double C-core output transformers.

Each Quest has a single RCA input and three binding posts, marked 0, 4 Ohm and 8 Ohm, on the right-hand side of the rear panel. Power enters through an IEC 320 mains inlet with a fuse drawer, and a rocker switch sits at the top left of the back panel.

Both amplifiers of a pair are shipped without their tubes installed. Audio Note quotes about 6000 hours of tube life and specifies replacement with matched pairs. At least 50 cm of free space is required above the amplifiers. The fascia is anodised aluminium or black acrylic, and the top plate is anodised aluminium or black anodised aluminium.

Pairing

A high-sensitivity loudspeaker is required. The standard version requires a preamplifier with RCA outputs, and the Low Gain version matches preamplifiers with a high output level.

Alternatives

The Conquest is the Audio Note mono power amplifier with two 300B triodes per channel in parallel single-ended.

Spezifikationen

  • Modellbezeichnung

    Quest

  • Eingangsempfindlichkeit (mV)

    160

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    100 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    8

  • Ausgangsleistung (4Ω) (W)

    8

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    N/A

  • Maximale Leistungsaufnahme (W)

    200

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    195 x 205 x 500

  • Gewicht (kg)

    27.5

  • Offizieller Link

Weitere Komponenten