Hifiverse

Phonovorstufen - Vitus Audio RP-102

Beschreibung, Bilder, technische Daten und Spezifikationen

Vitus Audio RP-102
Bildquelle - (c) Vitus Audio

The RP-102 is the phono stage of the Vitus Audio Reference Series, which the Danish company describes as its entry point and as cost-optimised versions of its Signature Series products. It succeeds the RP-100, and for this model Vitus redesigned the main board, the power supply and the logic control.

Key specs that matter

Inputs are one balanced XLR pair and two single-ended RCA pairs. Outputs are one XLR pair and one RCA pair, chosen in the menu, both with an output impedance of 80 ohms. MC gain is 51, 54, 57, 60, 63, 66, 69, 72 or 75 dB, and MM gain runs from 27 to 51 dB in the same 3 dB steps. MC loading has 23 steps from 40 ohms to 2 kohms, while MM loading has 15 steps from 40 ohms to 47 kohms. Frequency response extends beyond 800 kHz, signal-to-noise ratio is over 70 dB at 1 kHz and THD+N is below 0.01%. Power consumption is below 1 W in standby and 25 W in operation. The main unit measures 103 x 435 x 431 mm (H x W x D, including feet and binding post) and weighs 9.5 kg. Its external power supply measures 65 x 175 x 275 mm and weighs 4 kg.

Engineering and use context

On the MC side an Active Moving Coil step-up gain stage reaches 75 dB, and Vitus states that it supports most very low output MC cartridges with significantly lower noise. Power supply technology comes from the Signature and Masterpiece Series, and two 7-pin XLR power interconnects join the external supply to the main unit.

Load and gain settings are switched from the front panel or from an optional Apple remote, so neither the rear plate nor the case has to be opened for hardware changes. A MONO setting makes the RP-102 output a mono signal, for mono cartridges and original monaural pressings. Each input can be renamed or disabled in the menu, and auto standby is set from off to 360 minutes. A ground terminal on the rear panel accepts the turntable earth lead. Firmware is updated from a FAT or FAT32 USB drive through a service port under the front right side of the unit.

Pure White, Jet Black and Warm Silver are the standard finishes, and Titanium Orange, Dark Champagne and Titanium Grey are available as unique colours.

Pairing

A line-level preamplifier or integrated amplifier with an XLR or RCA input is required. Its balanced XLR input accepts a tonearm wired for balanced connection. The matching Reference Series line stage is the RL-102.

Alternatives

Vitus Audio's SP-103 is the Signature Series phono stage.

Spezifikationen

  • Modellbezeichnung

    RP-102

  • Eingänge (symmetrisch)

    1

  • Eingänge (unsymmetrisch)

    2

  • MC-Eingangsimpedanz (stromgekoppelt) (Ω)

    <2000

  • MM/MC-Eingangsimpedanz (spannungsgekoppelt) (Ω)

    N/A

  • Ausgangsimpedanz (Ω)

    80

  • Verstärkung (dB)

    N/A

  • Genauigkeit der Wiedergabe-Entzerrungskurven (dB)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    800 000

  • Klirrfaktor + Rauschen (%)

    <0.01

  • Abmessungen (mm)

    65 × 175 × 275

  • Gewicht (kg)

    4

  • Offizieller Link