Hifiverse

DACs - Allnic Audio RD-7500 OTL/OCL

Beschreibung, Bilder, technische Daten und Spezifikationen

Allnic Audio RD-7500 OTL/OCL
Bildquelle - (c) Allnic Audio

The RD-7500 OTL/OCL is a tube digital-to-analog converter from Allnic Audio, the company of designer Kang Su Park. It joins an ESS Technology converter chip to a single-stage analog section built on the 5687 dual triode, and its name states the topology of that output stage - output transformerless (OTL) and output capacitorless (OCL). Within the Allnic range of digital sources it holds the entry position.

Key specs that matter

The ES9039PRO does the decoding here. It is a 32-bit, 8-channel ESS device based on the fourth generation of the HyperStream architecture, and ESS rates the chip at about 132 dB of dynamic range per channel. PCM is accepted from 44.1 kHz to 384 kHz and DSD from DSD64 up to DSD512. The signal-to-noise ratio is given as 110 dB, the single-ended output impedance as 500 ohms. The chassis measures 355 x 445 x 140 mm.

Engineering and use context

Allnic describes its design target for the RD-7500 as a straight wire with gain, a stage that raises the level of the converted signal without altering it. The analog side uses one amplification stage only, where many solid-state and multi-stage circuits pass the signal through dozens of parts. The 5687 was picked for its linearity, low internal resistance and high transconductance, which let a single stage supply enough gain at a low output impedance while running without negative feedback. With no output transformer and no coupling capacitor in the path, the stage is direct-coupled and extends down to DC, so the leakage inductance and distributed capacitance of a transformer and the reactance of a series capacitor at low frequencies are both absent. Allnic describes the circuit as non-feedback, contrasting it with feedback designs that correct an error only after it appears.

Pairing

The RD-7500 sits between a digital source and an integrated amplifier or preamplifier, which receives its line-level analog output. An output impedance of a few hundred ohms suits the high input impedance of tube preamplifiers and of most solid-state line stages. Any computer or streaming transport whose digital output reaches those rates can feed it high-resolution PCM and DSD files. Owners of Allnic tube amplifiers or phono stages can keep the whole analog chain on vacuum tubes from the same maker.

Alternatives

Among other Allnic digital converters, the D-5000 DHT gives its output stage to directly heated triodes.

Spezifikationen

  • Modellbezeichnung

    RD-7500 OTL/OCL

  • Wandlungstyp

    N/A

  • Wandlerchip

    ES9039PRO

  • DSD-Kompatibilität

    k. A.

  • Parameter

    PCM: 44.1kHz – 384kHz / DSD: DSD64 – DSD512

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Verstärkung (dBu)

    5

  • Ausgangspegel (symmetrisch) (V)

    N/A

  • Ausgangspegel (unsymmetrisch) (V)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    500

  • Analogausgänge

    N/A

  • Signal-Rausch-Abstand (dB)

    110

  • Klirrfaktor + Rauschen (% at 22 kHz)

    N/A

  • Abmessungen (mm)

    355 x 445 x 140

  • Gewicht (kg)

    N/A

  • Offizieller Link