Hifiverse

DACs - Gryphon Audio DIABLO 300 DAC MODULE

Beschreibung, Bilder, technische Daten und Spezifikationen

Gryphon Audio DIABLO 300 DAC MODULE
Bildquelle - (c) Gryphon Audio

The Diablo 300 DAC Module is the optional internal digital-to-analogue converter for Gryphon's Diablo 300 integrated amplifier. Gryphon Audio Designs of Denmark states that it draws heavily on the engineering of its Kalliope DAC. It can be factory installed or added later, and with the converter inside the amplifier there are no external pre-power interconnects between DAC and amplifier. Like all Gryphon products, it is designed and built in Denmark.

Key specs that matter

Conversion uses one ESS Sabre ES9018 32-bit/384 kHz chip. Over USB the module accepts PCM at 44.1 - 384 kHz up to 32 bits and DSD64, DSD128, DSD256 and DSD512, the last two on Windows only. XLR and BNC inputs take PCM from 22.05 to 192 kHz, the Toslink input up to 96 kHz. Maximum balanced output is 2.15 V RMS. Signal-to-noise ratio is better than 110 dB unweighted (20 Hz - 20 kHz) and 113 dB A-weighted. THD+N is below 0.005% at 0 dB, output impedance is 22 ohms, and bandwidth is 0 - 192 kHz (-3 dB). The module measures 260 x 70 x 110 mm (W x H x D) and weighs 1.6 kg.

Engineering and use context

Five digital inputs are added to the amplifier's five analogue inputs - one Neutrik XLR socket for a balanced 110 ohm AES/EBU source, two 75 ohm BNC sockets with Teflon insulation for S/PDIF, one Toslink and one USB. The analogue section is true dual mono, Class A and DC-coupled, with zero negative feedback. Its output stages run from discrete, ultra-low-noise ±22 V DC regulated supplies, and the analogue section of the ES9018 has separate left and right supplies. Multiple local voltage regulators are also used.

No power is drawn from the computer's USB bus. A 12.5 farad SuperCap supply powers the USB module and acts, in Gryphon's words, as a virtual battery. Timing comes from a temperature-compensated crystal oscillator with better than 5 ppm accuracy. PCM has fast or slow roll-off digital filters, and DSD has 50, 60 or 70 kHz (-3 dB) filters. Analogue filtering is first-order for PCM and second-order for DSD, with silvered mica and polypropylene capacitors.

Two four-layer circuit boards with up to 70 µm copper carry PCB-mounted sockets. The module sits in its own grounded aluminium housing that shields against HF radiation. With it installed, the Diablo 300 display shows the source, sampling frequency, format, SuperCap charging status and active filter.

Pairing

The module requires a Diablo 300 integrated amplifier. Its BNC, XLR and USB inputs accept a CD transport, network streamer or computer.

Alternatives

The Diablo 120 DAC Module is the corresponding Gryphon converter module for the Diablo 120 integrated amplifier.

Spezifikationen

  • Modellbezeichnung

    DIABLO 300 DAC MODULE

  • Wandlungstyp

    N/A

  • Wandlerchip

    Sabre ES9018

  • DSD-Kompatibilität

    Ja

  • Parameter

    uo to 32bit/384KHz and DSD512

  • Untere Grenzfrequenz +/- 3dB (Hz)

    20

  • Obere Grenzfrequenz +/- 3dB (Hz)

    20 000

  • Verstärkung (dBu)

    N/A

  • Ausgangspegel (symmetrisch) (V)

    N/A

  • Ausgangspegel (unsymmetrisch) (V)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Analogausgänge

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (% at 22 kHz)

    <0,0050

  • Abmessungen (mm)

    260 x 70 x 110

  • Gewicht (kg)

    1.6

  • Offizieller Link