Hifiverse

Standlautsprecher - Manger P1

Beschreibung, Bilder, technische Daten und Spezifikationen

Manger P1
Bildquelle - (c) Manger

The p1 is a passive 2-way floorstanding loudspeaker from Manger Audio of Mellrichstadt, Germany. Its midrange and treble come from the Manger Sound Transducer, the bending-wave driver that Josef W. Manger began developing in 1968 and completed in 1974. A 200 mm woofer covers the lowest octaves in a sealed enclosure. Manger is a family business, now led by Daniela Manger, daughter of the founder.

Key specs that matter

Mid and high frequencies are reproduced by the Manger Sound Transducer W06, with a bandwidth of 360 Hz - 45 kHz and a rise time of 13 µs. Below it sits a 200 mm (8 in.) woofer of carbon fibre-paper sandwich design with a 42 mm voice coil. Crossover frequency is 360 Hz. Frequency range is 40 Hz - 45 kHz, sensitivity is 89 dB (1 W/1 m) and impedance is 4 ohms. Maximum SPL is 106 dB peak. Recommended amplifier power is 50 - 200 W. Dimensions are 1139 x 270 x 214 mm (H x W x D), and weight is 31 kg.

Engineering and use context

In the Manger Sound Transducer, bending waves propagate from the centre across a flexible membrane. A single membrane therefore covers a wide frequency range, and Manger states that it has no mechanical energy storage that releases energy with a delay. In the p1 this star-shaped transducer replaces a conventional midrange and tweeter and covers everything from the lower midrange upward. Production takes place in batches of ten, and each transducer is individually tested and measured. Only units within a production tolerance of less than ±0.5 dB receive a serial number.

Inside the cabinet, struts suppress housing resonances, and the transducer and woofer each have their own compartment. Manger rounds the outer edges of the cabinet to improve the radiation behaviour. Bi-wiring terminals are WBT nextgen Plasma Protect copper sockets and accept banana plugs or cable lugs. Drivers and terminal are fixed into the cabinet with threaded screws. Manger cf1 feet in precision plastic allow fine adjustment.

Finishes are matt or satin colours, real wood veneer and UltraHigh Gloss, and Manger offers almost any colour or veneer on request. The p1 is listed for Devialet SAM processing and the Linn Exakt filter, and with Linn Exakt the passive p1 runs as an active speaker.

Pairing

An amplifier stable into low impedance loads is required. The terminals allow bi-wiring or passive bi-amping. Devialet amplifiers with SAM and Linn Exakt systems are listed as compatible.

Alternatives

The p2 is Manger Audio's other passive 2-way floorstanding speaker, a sealed design with two passive radiators and an 8 ohm impedance.

Spezifikationen

  • Modellbezeichnung

    P1

  • Untere Grenzfrequenz +/- 3dB (Hz)

    40

  • Obere Grenzfrequenz +/- 3dB (Hz)

    40 000

  • Empfindlichkeit (dB at 1 W/1m)

    89

  • Impedanz (Ohms)

    4

  • Anforderungen an den Endverstärker (W)

    50 - 200

  • Verfügt über interne Verstärkung

    k. A.

  • Leistung der internen Verstärkung (W)

    N/A

  • Größe (sm)

    113.9 x 27.0 x 21.4

  • Gewicht (kg)

    31

  • Offizieller Link

Weitere Komponenten