Hifiverse

Kopfhörer - Audio-Technica ATH-ADX3000

Beschreibung, Bilder, technische Daten und Spezifikationen

Audio-Technica ATH-ADX3000
Bildquelle - (c) Audio-Technica

The ATH-ADX3000 is an open-air dynamic headphone from Audio-Technica, released in Japan on 1 November 2024 as the third model of the ADX series. Audio-Technica calls it an air dynamic headphone and states that it draws on the ATH-ADX5000, launched in 2017 as the first True Open Air Audio model. The ATH-ADX7000 sits above both.

Key specs that matter

Type is open-air dynamic with a 58 mm driver. Sensitivity is 98 dB/mW and impedance is 50 ohms. Frequency response is 5 Hz - 45 kHz, and maximum input is 700 mW. Weight is approx. 257 g without the cable. Each earcup has an A2DC connector jack. A detachable 3.0 m cable of OFC wire with an elastomer sheath and a gold-plated 6.3 mm stereo plug comes with a hard case.

Engineering and use context

Closed and semi-open headphones use the resonance of the housing to boost the low frequencies. In the ADX design the housing does not boost the bass. Its driver is designed to control the air flow with the front and the back of the housing open. According to Audio-Technica, an open driver has neither the air resistance of a sealed space nor an acoustic chamber for tuning the bass, so it has to produce a full-range signal down to the lowest frequency on its own.

Core Mount Technology (PAT.P), as on the ATH-ADX5000, sets the position of the baffle damper relative to the earpad. With it, the voice coil is placed at the point that divides the acoustic space between ear and housing into two halves.

Materials differ from the higher models. The ADX3000 has a housing of general-purpose aluminium with honeycomb punching, a magnetic circuit of pure iron, a frame of fibre-reinforced resin and velour earpads. In the ADX5000 these are a Permendur magnetic circuit and a magnesium alloy frame, and the ADX7000 combines a magnesium alloy frame with a circuit of non-oriented electrical steel. Unlike both, the ADX3000 carries no serial number. Every part was designed for a minimal build, and units are assembled by hand by a skilled team at the Naruse plant in Japan and tested before shipping.

Pairing

A headphone amplifier with a 6.3 mm output is required for the supplied cable. For a balanced connection Audio-Technica offers the detachable AT-B1XA/3.0 balanced headphone cable. Replacement earpads are listed as HP-ADX3000.

Alternatives

The ATH-ADX5000 is the open-air model one step up in the ADX series, rated at 420 ohms and 5 Hz - 50 kHz.

Spezifikationen

  • Modellbezeichnung

    ATH-ADX3000

  • Wandlerprinzip

    Dynamic or Isodynamic

  • Bauart

    Open

  • Tragestil

    Over-ear

  • Untere Grenzfrequenz +/- 10dB (Hz)

    5

  • Obere Grenzfrequenz +/- 10dB (Hz)

    45 000

  • Max. Schalldruckpegel (dBSPL (1 kHz @ 5% THD))

    N/A

  • Verbindungsart

    Wired

  • Anschluss (mm)

    A2DC connector jack

  • Empfindlichkeit (dBSPL (1 kHz/ 1 mW)))

    98

  • Impedanz (Ohm (1 kHz))

    50

  • Wiedergabedauer (hours)

    N/A

  • Gewicht (g)

    257

  • Offizieller Link