Hifiverse

Kopfhörerverstärker - Schiit Audio MJOLNIR

Beschreibung, Bilder, technische Daten und Spezifikationen

Schiit Audio MJOLNIR
Bildquelle - (c) Schiit Audio

The Mjolnir 3 is the third generation of the Mjolnir, sold by Schiit Audio at USD 1,199 as a class A headphone amp and preamp. Schiit specifies it as 100% class A, no-feedback, dual-mono, choke-input, fully discrete and balanced differential. Earlier Mjolnirs were circlotron-style designs, one of them with tubes. This version is a new design that keeps the 100 V front-end stage of the Mjolnir 1. Chassis and transformers are made in California, PCBs in California or Nevada, and assembly is in San Antonio under a 5-year limited warranty.

Key specs that matter

Frequency response is 20 Hz - 20 kHz (±0.01 dB) and 2 Hz - 700 kHz (-3 dB). From the balanced 4-pin XLR jack, maximum power is 2 W RMS per channel into 32 ohms and 1 W into 300 ohms, with THD below 0.015% (20 Hz - 20 kHz, 4 V RMS, 300 ohms), CCIF IMD below 0.02%, SNR above 110 dB (A-weighted, ref. 4 V RMS), crosstalk better than -90 dB and output impedance below 0.25 ohm. The 6.35 mm single-ended jack gives 1 W into 32 ohms and 500 mW into 300 ohms, THD below 0.025% (2 V RMS, 300 ohms), SNR above 98 dB (ref. 2 V RMS), crosstalk better than -85 dB and output impedance below 0.13 ohm. Input impedance is 50 kohms. Gain is 2 (6 dB) or 8 (18 dB) from the balanced input and 1 (0 dB) or 4 (12 dB) from the single-ended input. Size is 406 x 203 x 51 mm, weight 7.3 kg and typical consumption 50 W.

Engineering and use context

Equipoise is Schiit's name for the gain stage, a complementary-pair, fully discrete, high-voltage, balanced differential circuit with zero feedback, DC coupled in and out. Its signal stays balanced from input through a 4-gang potentiometer to output. One switch selects single-ended class A, with the output stage biased by a fixed current source, or push-pull class A, with the current source modulated for more power. A second switch adds overall feedback. Gain changes through degeneration of the input stage, independent of feedback. Each channel has its own 48 VA transformer, choke, 100 V front-end rail and discrete regulation, with over 20,000 µF of filter capacitance per channel. Two Gjallarhorn heatsinks carry 16 bipolar NPN output devices rated at 10 A per channel. Inputs are relay switched. There is no DAC, microprocessor or motorised potentiometer, and Schiit states that the amplifier runs hot.

Pairing

Schiit recommends the amplifier for difficult headphones and advises against IEMs. A source with XLR outputs uses the balanced input. Switchable balanced and single-ended line outputs connect to active monitors or a power amplifier.

Alternatives

The Schiit Jotunheim 3 is a balanced headphone amplifier and preamplifier from the same range.

Spezifikationen

  • Modellbezeichnung

    MJOLNIR

  • Maximale Leistung, 32 Ohm (mW RMS per channel)

    2000 (XLR), 1000 (RCA)

  • Maximale Leistung, 50 Ohm (mW RMS per channel)

    N/A

  • Maximale Leistung, 300 Ohm (mW RMS per channel)

    1000 (XLR), 500 (RCA)

  • Maximale Leistung, 600 Ohm (mW RMS per channel)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    20

  • Obere Grenzfrequenz +/- 3dB (Hz)

    20 000

  • Verstärkung (dBu)

    N/A

  • Klirrfaktor (THD) (% at 1V RMS, 300 ohms)

    <0.015 (XLR), <0.025 (RCA)

  • Signal-Rausch-Abstand (dB)

    >110 (XLR), >98 (RCA)

  • Intermodulationsverzerrung (IMD) (%, CCIR, 300 Ohms)

    <0.02 (XLR), <0.03 (RCA)

  • Übersprechen (dB, 20Hz-20KHz, 300 Ohms)

    >90 (XLR), >85 (RCA)

  • Ausgangsimpedanz (Ohms)

    0.25 (XLR), 0.13 (RCA)

  • Abmessungen (mm)

    406 x 203 x 51

  • Gewicht (kg)

    7.3

  • Offizieller Link

Weitere Komponenten