Hifiverse

Vorverstärker - Chord ULTIMA PRE

Beschreibung, Bilder, technische Daten und Spezifikationen

Chord ULTIMA PRE
Bildquelle - (c) Chord

The ULTIMA PRE is the flagship preamplifier of Chord Electronics and part of the ULTIMA Reference range. Chord created it as the partner for the ULTIMA mono power amplifier and describes it as the product of three decades of research, design and engineering in the UK. Every unit is hand-made in the Kent factory, with the stages of build and production overseen by one technician. Its double-height enclosure is aircraft-grade aluminium and stands on the Integra Leg System, offered in Argent silver or Jett black.

Key specs that matter

There are eight stereo inputs, four on balanced XLR and four on unbalanced RCA, plus one balanced XLR AV bypass input. Three selectable stereo outputs are available on both XLR and RCA. Frequency response is 10 Hz - 200 kHz (±3 dB), THD is 0.002% (20 Hz - 20 kHz), and signal-to-noise ratio is -120 dB on all inputs. Input impedance is 100 kohm, output impedance is 100 ohms, and channel separation is 100 dB. Maximum input voltage is 10 V RMS and maximum output voltage 17 V RMS. Gain is selectable per input in six steps - x0.5, x1, x1.5, x2, x2.5 and x3. Dimensions are 420 x 355 x 310 mm (W x D x H) without the Integra legs and 480 x 355 x 350 mm with them, and weight is 30 kg.

Engineering and use context

Chord uses true dual-mono construction with separate ultra-high-frequency switch mode power supplies for each channel. Circuitry is fully balanced, the signal path is analogue, and inputs and outputs are buffered. Volume is set by a Blue Velvet ALPS potentiometer. Solid milled aluminium shielding protects the sensitive internal circuits against RF interference. Cooling is by convection, and internal thermal protection shuts the unit down at excessive temperatures.

On the fascia are the display, the volume and balance dials, two 1/4 inch headphone sockets and four EQ frequency controls, one for high and one for low frequencies per channel. This EQ acts on all inputs and outputs except the AV bypass and the tape loop, and it can be switched off. Two input selection buses are provided - Bus A is permanently connected to the T1 recording output and Bus B to T2, so two sources can be recorded at the same time. In AV bypass mode the volume control and signal processing are bypassed, and a separate AV Bypass Monitor output is provided. Three teal light rings illuminate the top panel. A metal IR system remote and 12 V trigger input and output complete the control set, and the warranty is five years.

Pairing

The matching power amplifier is the ULTIMA mono. Each output drives a 68 ohm load, on XLR or RCA. A surround processor connects to the XLR AV bypass input. With a Chord Electronics DAC the line gain is set to 0.5.

Alternatives

The ULTIMA PRE 3 is Chord's five-input preamplifier in the ULTIMA range.

Spezifikationen

  • Modellbezeichnung

    ULTIMA PRE

  • Analogeingänge (symmetrisch)

    4

  • Analogeingänge (unsymmetrisch)

    4

  • Analogausgänge (symmetrisch)

    3

  • Analogausgänge (unsymmetrisch)

    3

  • Verstärkung (dBu)

    N/A

  • Eingangsempfindlichkeit (mV)

    N/A

  • Ausgangsspannung (V)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    100 000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    100 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    100

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    100

  • Maximaler Ausgangspegel (symmetrisch) (dBu)

    N/A

  • Maximaler Ausgangspegel (unsymmetrisch) (dBu)

    N/A

  • Regelbereich der Lautstärke (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    10

  • Obere Grenzfrequenz +/- 3dB (Hz)

    200 000

  • Signal-Rausch-Abstand (SNR, unbewertet) (dB)

    117

  • Klirrfaktor + Rauschen (THD+N) (%)

    0.002

  • Abmessungen (mm)

    420 x 355 x 310

  • Gewicht (kg)

    30

  • Offizieller Link

Weitere Komponenten