Hifiverse

Vorverstärker - Schiit Audio SAGA 2

Beschreibung, Bilder, technische Daten und Spezifikationen

Schiit Audio SAGA 2
Bildquelle - (c) Schiit Audio

Saga 2 is a remote-controlled preamplifier from Schiit Audio, priced at USD 279 and built in the USA. Schiit lists it as a relay-potentiometer, passive-or-active, Class A, zero-feedback, 100% discrete and differential design with a 75 V linear power supply and a headphone output. Compared with the earlier Saga, Saga+ and Saga S it adds balanced outputs and switchable gain, has no tube option and uses a wall wart instead of direct AC input.

Key specs that matter

Inputs are 4 RCA pairs, selectable via the front switch or the remote. Outputs are 1 XLR pair and 1 RCA pair, both active at the same time. Input impedance is 10 kohms in all modes. Low gain is 1x/2x and high gain is 4x/8x (SE/balanced), with 75 ohms output impedance and maximum output above 10 V RMS in both settings. THD is below 0.001% (20 Hz - 20 kHz, 2 V RMS) and CCIR IMD is below 0.001%. SNR is above 124 dB on low gain and above 116 dB on high gain (A-weighted, ref. 2 V RMS). Frequency response is 20 Hz - 20 kHz (-0.5 dB) and 3 Hz - 200 kHz (-3 dB). In passive mode output impedance varies up to 4.8 kohms, and THD and IMD are unmeasurable on an APx555. Dimensions are 229 x 152 x 38 mm (W x D x H), and weight is 1.4 kg.

Engineering and use context

The gain stage is Equipoise, a differential discrete Class A circuit with zero feedback on 75 V rails. Its output stages run in single-ended, current-sourced Class A inside a differential gain configuration, and apart from emitter degeneration there is no feedback. According to Schiit, this gain stage is similar to the discrete buffer of Skoll and Freya+.

Volume is set by a relay-switched stepped attenuator with discrete 0.5% thin-film resistors in 64 steps of 1 dB. Only a few resistors and relay switches are in the signal path, and channel matching is held across the whole range. The relays click during adjustment, and the output can drop out briefly when many relays change at once. A headphone stage is also included, a booster based on the OPA1656 rated at 150 mW typical maximum output.

Power comes from a 24 VAC/6 VAC wall wart, and internal +45 V/-28 V and 5 V/3.3 V rails are derived from it. Besides the standard IR remote, Saga 2 supports the Forkbeard app control system with an optional Forkbeard module. Final assembly is in Corpus Christi, and warranty is 3 years.

Pairing

Sources are single-ended RCA, as there are no balanced inputs. The XLR output can drive Schiit Gjallarhorn, Aegir 2 or Vidar 2 amplifiers in balanced mono mode. Passive mode requires short cables and a high-impedance amplifier input. Schiit names Modius and Bifrost as matching DACs.

Alternatives

The Schiit Kara F, priced at USD 799, is a balanced preamplifier and headphone amplifier.

Spezifikationen

  • Modellbezeichnung

    SAGA 2

  • Analogeingänge (symmetrisch)

    N/A

  • Analogeingänge (unsymmetrisch)

    4

  • Analogausgänge (symmetrisch)

    1

  • Analogausgänge (unsymmetrisch)

    1

  • Verstärkung (dBu)

    N/A

  • Eingangsempfindlichkeit (mV)

    N/A

  • Ausgangsspannung (V)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    75

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    75

  • Maximaler Ausgangspegel (symmetrisch) (dBu)

    N/A

  • Maximaler Ausgangspegel (unsymmetrisch) (dBu)

    N/A

  • Regelbereich der Lautstärke (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    20

  • Obere Grenzfrequenz +/- 3dB (Hz)

    20 000

  • Signal-Rausch-Abstand (SNR, unbewertet) (dB)

    >116 (high gain), >124 (low gain)

  • Klirrfaktor + Rauschen (THD+N) (%)

    <0.001

  • Abmessungen (mm)

    229 x 152 x 38

  • Gewicht (kg)

    1.4

  • Offizieller Link

Weitere Komponenten