Hifiverse

Endstufen Stereo - McIntosh MC303

Beschreibung, Bilder, technische Daten und Spezifikationen

McIntosh MC303
Bildquelle - (c) McIntosh

The MC303 is a three-channel solid-state power amplifier from McIntosh Laboratory of Binghamton, New York. McIntosh designed it for the front left, front right and centre channels of a home theatre and describes it as its most powerful multi-channel amplifier offering to date. It is also the first multi-channel McIntosh amplifier with Autoformer-coupled output stages. In a music system it can be used for tri-amping compatible loudspeakers such as the McIntosh XRT1.1K or XRT2.1K.

Key specs that matter

Rated output is 300 W per channel into 2, 4 or 8 ohms, all channels operating, over a rated power band of 20 Hz - 20 kHz. Available peak power is 1,200 W per channel, and output current is 60 A. THD is 0.005% maximum from 250 mW to rated power. Frequency response is 20 Hz - 20 kHz (+0, -0.25 dB) and 10 Hz - 100 kHz (+0, -3 dB). Signal-to-noise ratio is 112 dB (A-weighted) below rated output, dynamic headroom is 1.8 dB and the wide-band damping factor is greater than 40. Input sensitivity for rated output is 1.7 V unbalanced and 3.4 V balanced, with an input impedance of 10,000 ohms. The amplifier measures 450.9 x 314.3 x 558.8 mm (W x H x D, including feet, front panel and cables) and weighs 70.3 kg.

Engineering and use context

Each channel uses a push-pull complementary output stage with ThermalTrak output transistors, coupled to the speaker terminals through McIntosh Output Autoformers. According to McIntosh, the Autoformers provide a match between the output stages and loads of 2, 4 and 8 ohms and also give DC protection for the loudspeakers. Separate output connections for each impedance are provided on large gold-plated five-way binding posts.

Power Guard is a waveform comparison circuit that monitors input and output signals and adjusts the input level to avoid clipping, with less than 2% THD at up to 14 dB of overdrive. Sentry Monitor is a fuse-less short-circuit protection circuit that disengages the output stage before current exceeds the safe operating level and resets automatically. Thermal protection circuits guard against overheating. A regulated power supply with a large power transformer and capacitors is used.

Three peak-reading watt meters sit behind a 12.7 mm glass faceplate, and their illumination can be switched off for theatre use. The chassis is mirror-polished stainless steel with machined, anodised aluminium handles.

Pairing

A preamplifier or A/V processor with balanced or unbalanced outputs is required. A speaker between two ratings connects to the nearest lower impedance terminal. For surround channels McIntosh names the MC312 and MC152 stereo power amplifiers.

Alternatives

The MC257 is a McIntosh home theatre power amplifier rated at 250 W x 3 channels or 200 W x 7 channels.

Spezifikationen

  • Modellbezeichnung

    MC303

  • Eingangsempfindlichkeit (mV)

    3400 (XLR) + 1700 (RCA)

  • Eingangsimpedanz (symmetrisch) (Ω)

    10 000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    300

  • Ausgangsleistung (4Ω) (W)

    300

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    10

  • Obere Grenzfrequenz +/- 3dB (Hz)

    100 000

  • Signal-Rausch-Abstand (dB)

    112

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    0.005

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    >40

  • Abmessungen (mm)

    450.9 x 314.3 x 558.8

  • Gewicht (kg)

    70.3

  • Offizieller Link

Weitere Komponenten