Hifiverse

Endstufen Stereo - Pro-Ject Amp Box RS2

Beschreibung, Bilder, technische Daten und Spezifikationen

Pro-Ject Amp Box RS2
Bildquelle - (c) Pro-Ject

The Pro-Ject Amp Box RS2 is a high-end stereo power amplifier in the compact Box Design format, switchable into bridge mode as a single mono amplifier. Pro-Ject describes it as its reference power amplifier design. It is made in Europe, comes in silver or black, and its MSRP is EUR 1,799 including VAT.

Key specs that matter

Rated output is 2 x 80 W into 8 ohms and 2 x 130 W into 4 ohms (1% THD), and 280 W into 8 ohms in bridge mode. Peak power is 2 x 100 W into 8 ohms, 2 x 160 W into 4 ohms and 350 W bridged. Gain is 27 dB. Frequency response is 20 Hz - 20 kHz (< -0.2 dB), THD is below 0.08% at 20 W into 4 ohms, and signal-to-noise ratio is 97 dBV (100 dBV A-weighted). Input impedance is 47 kOhm on RCA and 20 kOhm on XLR. Dimensions are 206 x 85 x 227 mm (W x H x D, with sockets), and weight is 2.66 kg without the power supply.

Engineering and use context

It is a hybrid, fully discrete class AB design. The input is a differential stage with a 6922 (6DJ8) double triode, followed by a stage with 2SA1552T and 2SC4027T transistors, and the output stage is a pair of STD03N and STD03P transistors in class AB. A DC servo holds the output at zero DC voltage. In standby the amplifier stays connected to its supply, and power-off is achieved by disabling the current sources.

Protection includes a DC detector that disconnects the speakers and lights an LED, a thermal shutdown with its own indicator and a clipping LED. Power comes from an external ±40 V/5 A DC supply, and standby consumption is below 0.5 W. Inputs are switched on the front panel or via RS232 on a 3-pin terminal block, and a 12 V trigger input on a 2.5 mm jack switches the unit on with other Box Design components. According to Pro-Ject, its full metal casing protects against vibration and interference and is also important for heat emission.

Pairing

A preamplifier with balanced XLR or RCA outputs is required. Speakers of 8 ohms or higher are required in bridge mode. Its speaker terminals accept 4 mm bananas, spades or bare wire. The Power Box RS2 Amp linear supply raises output by up to 25%.

Alternatives

The Pro-Ject Amp Box DS2 is the class D stereo power amplifier of the Box Design range.

Spezifikationen

  • Modellbezeichnung

    Amp Box RS2

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    20000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    47000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    2 x 80

  • Ausgangsleistung (4Ω) (W)

    2 x 130

  • Verstärkung (dBu)

    27

  • Untere Grenzfrequenz +/- 3dB (Hz)

    20

  • Obere Grenzfrequenz +/- 3dB (Hz)

    20000

  • Signal-Rausch-Abstand (dB)

    97

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    0.08

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    206 x 85 x 227

  • Gewicht (kg)

    2.66

  • Offizieller Link

Weitere Komponenten