Hifiverse

Endstufen Stereo - Pro-Ject Amp Box RS

Beschreibung, Bilder, technische Daten und Spezifikationen

Pro-Ject Amp Box RS
Bildquelle - (c) Pro-Ject

The Amp Box RS is a stereo power amplifier from Pro-Ject Audio Systems of Austria and belongs to the RS line of its compact Box Design electronics. Pro-Ject lists four specific characteristics for it - a fully balanced double mono design, energy-saving PWM modules, a tube buffer input stage and an upgrade option to the PS Box RS linear power supply. MSRP was EUR 899 including VAT, with the casing available in silver or black.

Key specs that matter

Power output is 2 x 110 W into 8 ohms and 2 x 180 W into 4 ohms with both channels driven. Gain is 26 dB. THD is below 0.05% at 100 W, and signal-to-noise ratio is better than 100 dB (IEC-A). Channel separation is better than 100 dB at 20 kHz. Frequency response is 10 Hz - 50 kHz (-0.8 dB / -3 dB). Damping factor is 400 at 8 ohms and 200 at 4 ohms. Input sensitivity is 1.35 V and input impedance is 22 kohms. Line-level inputs are one pair of RCA and one pair of XLR sockets, with XLR pin 2 hot and pin 3 cold. Including sockets, the casing measures 206 x 72 x 220 mm (W x H x D), and weight is 2,120 g without the power supply.

Engineering and use context

Its tube buffer input stage uses two ECC88 (6922) tubes. Behind this buffer, the output stages are highly efficient PWM modules, and Pro-Ject quotes a conversion efficiency from mains to output power of 92%. Each channel is a separate balanced circuit in a fully balanced double mono layout. SMD construction is used for the shortest signal paths.

A metal casing protects the circuitry against vibration and interference. Power comes from an external 48 V / 2.5 A DC supply that accepts 100 - 240 V at 50/60 Hz, and standby consumption is below 1 W. The optional PS Box RS linear power supply raises the rating to 180 W per channel into 8 ohms and 250 W per channel into 4 ohms. Speaker terminals take 4 mm banana plugs, spades or bare wire, and a push button next to the input sockets selects RCA or XLR. A switch on the front panel toggles between on and standby, and its blue LED blinks until the tubes reach operating temperature. Pro-Ject also names the Amp Box RS for bi-amping and tri-amping applications, with one unit per driver section of the loudspeaker.

Pairing

The matching preamplifier is the Pre Box RS. Its XLR inputs accept a balanced connection from any preamplifier with balanced outputs. The manual specifies one loudspeaker of not less than 4 ohms per channel. Loudspeakers with separate bass and treble terminals allow bi-amping with two units.

Alternatives

The Amp Box DS2 is another Pro-Ject stereo power amplifier in the Box Design range.

Spezifikationen

  • Modellbezeichnung

    Amp Box RS

  • Eingangsempfindlichkeit (mV)

    1350

  • Eingangsimpedanz (symmetrisch) (Ω)

    22 000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    22 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    110

  • Ausgangsleistung (4Ω) (W)

    180

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    10

  • Obere Grenzfrequenz +/- 3dB (Hz)

    50 000

  • Signal-Rausch-Abstand (dB)

    >100

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    < 0.05

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    400

  • Abmessungen (mm)

    206 x 72 x 200

  • Gewicht (kg)

    2.12

  • Offizieller Link

Weitere Komponenten