Hifiverse

Endstufen Mono - Fluo DM125

Beschreibung, Bilder, technische Daten und Spezifikationen

Fluo DM125
Bildquelle - (c) Fluo

The DM125 is the entry power amplifier of FLUO, an audio brand based in Winchester, England. FLUO works under the creative direction of Keith Martin, who founded the power conditioning company IsoTek in 1999. Its range consists of the Jubilee turntable, the Pre1 preamplifier, the DM125 and DM250 stereo power amplifiers and the M500 monoblock. FLUO describes the DM125 as a dual mono power amplifier in a single chassis, with two separate amplifier circuits for the left and right channels.

Key specs that matter

Output power is 125 W into 8 ohms, 250 W into 4 ohms and 500 W into 2 ohms short-term, all into resistive loads with 230 V AC mains. Idle power consumption is 70 W. A 6.3 A slow-blow mains fuse limits long-term consumption to 1,450 W per channel, so long-term sine wave power into 2 ohms is below 500 W. Input impedance is 40 kOhm on the balanced 3-pin XLR input (pin 2 plus, pin 3 minus, pin 1 ground) and 20 kOhm on the unbalanced RCA input. Minimum load allowed by the protection system is 1.5 ohms. Dimensions are 485 x 270 x 535 mm (W x H x D).

Engineering and use context

Each channel uses its own capacitors, rectifiers and mains transformer windings. When a large power demand lowers the voltage of the right channel capacitors, the voltage of the left channel capacitors stays the same, and vice versa. FLUO contrasts this with a conventional stereo amplifier, where both channels share one set of capacitors and the same voltage drop. Output devices are Single Die MOSFETs, and the design doubles its power each time the load impedance halves.

A protection system checks for abnormal high frequencies, voltage, current, phase angle and load. If a signal is outside the limits, for example from a frayed loudspeaker wire causing a short circuit, it mutes the input for 1 second and then tests for 1 ms whether the fault is still present. Once the fault is removed, playback resumes automatically. Audio is also muted when the operating temperature exceeds the set limits. According to FLUO, the chassis, heat sink fins, top and front panel diffuse sound waves up to beyond 20 kHz and reduce resonance frequencies.

Pairing

A preamplifier with a balanced XLR or unbalanced RCA output is required. FLUO recommends shielded signal cables. The matching FLUO preamplifier is the Pre1.

Alternatives

The FLUO DM250 is the larger dual mono model, with 250 W into 8 ohms, two mains power cords and two separate mains transformers.

Spezifikationen

  • Modellbezeichnung

    DM125

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    40 000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    20 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    125

  • Ausgangsleistung (4Ω) (W)

    250

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    N/A

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    485 x 270 x 535

  • Gewicht (kg)

    N/A

  • Offizieller Link

Weitere Komponenten