Hifiverse

Vollverstärker - Accuphase E-5000

Beschreibung, Bilder, technische Daten und Spezifikationen

Accuphase E-5000
Bildquelle - (c) Accuphase

The Accuphase E-5000 is a high-power Class AB integrated stereo amplifier, developed as the fourth model for the company's 50th anniversary. Accuphase introduced it as its flagship high-power Class AB integrated amplifier, and it is the largest Class AB integrated model in the range. Its circuit is balanced from input to output, combining Balanced AAVA volume control with an instrumentation amplifier power stage.

Key specs that matter

Rated continuous average output is 240 W per channel into 8 ohms and 320 W into 4 ohms, both channels driven, 20 - 20,000 Hz. THD is 0.05% (4 - 16 ohms) and IMD 0.01%. Frequency response is 3 - 150,000 Hz (0, -3.0 dB) at 1 W via MAIN IN. Damping factor is 1,000 (8 ohms, 50 Hz). S/N ratio at rated output is 111 dB via INPUT and 126 dB via MAIN IN. Inputs are five line and two balanced, with a recorder loop. Dimensions are 465 x 211 x 502 mm (W x H x D), and weight is 33.8 kg.

Engineering and use context

AAVA (Accuphase Analog Vari-gain Amplifier) removes variable resistors from the signal path. Two AAVA modules per channel are used in a fully balanced configuration, and the preamplifier section is balanced up to the tone control circuit and output buffer. Accuphase quotes equivalent input noise of -124 dB (0.63 µV). An in-house volume sensor, made by aluminium block extrusion, reads the knob position. Its motor and gears sit on a floating mechanism decoupled from the chassis by silicone rubber.

Each channel has a large heat sink and five parallel push-pull pairs of bipolar transistors in Class AB. This power amplifier engine has the same circuit configuration as the P-7300 and uses current feedback. A specially made toroidal transformer and two 40,000 µF/100 V filtering capacitors are mounted in the centre of the mono-block chassis. Protection relies on low-impedance MOS-FET switches.

On the front are needle power meters, tone controls with summing active filters, a loudness compensator, phase setting per input and a -20 dB attenuator. A discrete headphone amplifier is built in, and the RC-250 remote is supplied. Two rear slots take option boards such as the DAC-60 with two ESS ES9016K2M chips or the AD-50 phono board for MM and MC.

Pairing

Speaker set A accepts 4 - 16 ohm loads, while speaker set B is rated for 8 - 16 ohms. Pre outs allow bi-amping, and MAIN IN allows use as a power amplifier alone. Headphones of 8 ohms or higher are supported.

Alternatives

The Accuphase E-4000 is the smaller Class AB integrated model, rated at 180 W per channel into 8 ohms.

Spezifikationen

  • Modellbezeichnung

    E-5000

  • Typ

    PRECISION INTEGRATED STEREO AMPLIFIER

  • Analogeingänge (symmetrisch)

    2

  • Analogeingänge (unsymmetrisch)

    5

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • D/A-Wandlung

    k. A.

  • Phono MM/MC-Eingangsimpedanz (stromgekoppelt) (Ω)

    N/A

  • Ausgangsleistung (8Ω) (W)

    240

  • Ausgangsleistung (4Ω) (W)

    320

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (%)

    N/A

  • Dämpfungsfaktor

    1000

  • Abmessungen (mm)

    465 x 502 x 211

  • Gewicht (kg)

    33.8

  • Offizieller Link

Weitere Komponenten