Hifiverse

Vollverstärker - ToneWinner AD-2PRO+

Beschreibung, Bilder, technische Daten und Spezifikationen

ToneWinner AD-2PRO+
Bildquelle - (c) ToneWinner

The AD-2PRO+ is a 2.1-channel integrated amplifier from Tone Winner, the Guangzhou audio manufacturer. Its output stage runs in Class A, Class AB or an Auto mode that switches between the two, selected with one key on the remote control. The same chassis carries an ES9038 DAC with USB-Audio input, an MM/MC phono stage and balanced and unbalanced subwoofer outputs.

Key specs that matter

Power output is 240 W per channel (THD 1%, 1 kHz, 8 ohms, one channel driven), and rated impedance is 8 ohms. Gain is 40 dB ±1 dB. Frequency response is 15 Hz - 95 kHz (+1/-3 dB), S/N is ≥100 dB (A-weighted) and THD is ≤0.05% (1 kHz, A-weighted). Analogue inputs are one balanced XLR, two unbalanced RCA and MM/MC phono. Digital inputs are two optical, one coaxial and USB. USB accepts PCM 16-32 bit at 44.1-768 kHz, DSD64 to DSD512 and DoP up to DoP256, while optical and coaxial accept PCM up to 192 kHz and DoP64. Power consumption is 260-320 W in Class A and 70-110 W in Class AB. Dimensions are 444 x 254 x 460 mm (W x H x D), and net weight is 35.9 kg.

Engineering and use context

Tone Winner describes the circuit as fully balanced and fully symmetrical, from a differential input to a differential BTL power output. A cascode circuit forms the input stage, and the voltage amplifier stage uses a common-base circuit. Its output stage uses a three-stage Darlington driver and a total of 24 Toshiba 1943/5200 transistors in parallel. Nine TI OPA1656 operational amplifiers make up the balanced amplification of the preamplifier and DAC sections, and volume is set by an NJW1195A controller chip in 0.5 dB steps.

Left and right channels have independent power supplies, with an 860 W toroidal transformer and 16 capacitors totalling 128,800 µF. The preamplifier and power amplifier run from separate high and low voltage rails under a two-level power management circuit. Input, power storage, power supply and amplifier sections occupy separate chambers. Protection covers short circuit, overheating, high frequency and DC. A patented wide-voltage design switches automatically between AC 110 V and 220 V.

Pairing

Speakers with a nominal impedance of 8 ohms are the rated load. The power amplifier mode allows use with an external preamplifier. Speaker output selection A, B or A+B allows bi-wiring, and an active subwoofer connects via XLR or RCA.

Alternatives

Tone Winner's AD-3PRO+ is another integrated amplifier with the same Class A, Class AB and Auto modes, XLR and RCA inputs, DSD decoding and an MM/MC phono stage.

Spezifikationen

  • Modellbezeichnung

    AD-2PRO+

  • Typ

    Integrated Amplifier

  • Analogeingänge (symmetrisch)

    1

  • Analogeingänge (unsymmetrisch)

    3

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • D/A-Wandlung

    k. A.

  • Phono MM/MC-Eingangsimpedanz (stromgekoppelt) (Ω)

    N/A

  • Ausgangsleistung (8Ω) (W)

    250

  • Ausgangsleistung (4Ω) (W)

    N/A

  • Verstärkung (dBu)

    40

  • Untere Grenzfrequenz +/- 3dB (Hz)

    15

  • Obere Grenzfrequenz +/- 3dB (Hz)

    95 000

  • Signal-Rausch-Abstand (dB)

    >100

  • Klirrfaktor + Rauschen (%)

    ≤0.002

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    444 x 254 x 460

  • Gewicht (kg)

    35.9

  • Offizieller Link

Weitere Komponenten