Hifiverse

Vollverstärker - Aavik Aavik I-580

Beschreibung, Bilder, technische Daten und Spezifikationen

Aavik Aavik I-580
Bildquelle - (c) Aavik

The Aavik I-580 is a stereo integrated amplifier from Aavik, one of the three brands of Audio Group Denmark in Aalborg, alongside Ansuz and Børresen. It belongs to the I-180, I-280 and I-580 trio, which share one user guide and one specification table, and of the three only the 580 has a solid copper inner chassis, together with the largest number of Ansuz noise-reduction circuits. Aavik integrates the Tesla coil technologies of its sister brand Ansuz into its products.

Key specs that matter

Output is 2 x 300 W into 8 ohms and 2 x 600 W into 4 ohms. THD+N is below 0.006% (1-100 W, 1 kHz, 8 ohms), IMD below 0.002% and TIM below 0.008% (both 1-100 W, 4 ohms). There are five single-ended RCA line inputs with 10 kohms input impedance. Gain is adjustable from 5 to 15 dB on inputs 1-4 (maximum input 4.5 V RMS) and from 1 to 11 dB on input 5 (6.5 V RMS). One RCA pre out gives up to 7.5 V RMS from a 50 ohm output impedance, with line-stage distortion below 0.005% (1 kHz, 1 V input). Volume has 76 steps of 1 dB. Noise reduction counts 108 active Tesla coils, 240 active square Tesla coils, 11 dither circuits and 4 anti aerial resonance coils. Consumption is below 0.5 W in standby and below 50 W at idle. Dimensions are 400 x 384 x 102 mm (L x W x H), and weight is 10.7 kg.

Engineering and use context

Amplification uses the patented Aavik UMAC switching amplifier technology. PWM is generated with sine wave modulation instead of triangle modulation, so less inductive filtering is required at the output, and Aavik states that the lower output inductance gives a better damping factor. Dual mixed mode feedback is also applied. In the line stage an inverted, virtual ground amplifier topology allows a gain lower than 1.

Its resonant mode power supply is driven by sine waves rather than square waves, and its operating frequency rises when more power is needed. Ultra-low noise regulators supply the individual circuit sections. Active Tesla coils are powered, and Aavik quotes them as three to four times as efficient as passive ones, while the square versions are embedded in the circuit boards with the counter coil on the rear side. The cabinet uses a natural-based composite material, with aluminium reduced to what cooling requires.

Pairing

Speaker terminals accept spade connectors or 4 mm banana plugs. The pre out allows a power amplifier, active subwoofer or headphone amplifier, and two 12 V DC trigger outputs switch them on with the I-580. One input can be set as a home-theatre bypass with fixed volume.

Alternatives

The Aavik I-880 is the integrated amplifier of the 880 series, with 132 active Tesla coils, 20 active zirconium Tesla coils and a switchless optical input board.

Spezifikationen

  • Modellbezeichnung

    Aavik I-580

  • Typ

    Integrated Amplifier

  • Analogeingänge (symmetrisch)

    N/A

  • Analogeingänge (unsymmetrisch)

    5

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    10 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    50

  • D/A-Wandlung

    k. A.

  • Phono MM/MC-Eingangsimpedanz (stromgekoppelt) (Ω)

    N/A

  • Ausgangsleistung (8Ω) (W)

    300

  • Ausgangsleistung (4Ω) (W)

    600

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (%)

    <0,006

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    400 x 384 x 102

  • Gewicht (kg)

    10.7

  • Offizieller Link

Weitere Komponenten