Hifiverse

Phonovorstufen - Karan Acoustics PHONOa

Beschreibung, Bilder, technische Daten und Spezifikationen

Karan Acoustics PHONOa
Bildquelle - (c) Karan Acoustics

The PHONOa is a dual mono balanced phono preamplifier with an external power supply from Karan Acoustics, part of its Master Collection. Karan Acoustics was founded in 1986 by Milan Karan, and its first high-end audio designs appeared at the end of 1989. The PHONOa consists of a main control unit and the PSUa power supply unit, connected by an umbilical cable.

Key specs that matter

There are three phono inputs, each available as single-ended RCA or balanced XLR (6 sockets in total), and two line outputs, one RCA and one XLR. Gain is adjustable from 48 to 71 dB. Phono EQ settings are RIAA (±0.1 dB), EMI, Decca and Columbia (±0.15 dB) and Teldec (±0.1 dB). Output impedance is 90 ohms, and output level is 1.55 V RMS nominal and 18.0 V RMS maximum (balanced, 600 ohm load). Frequency response is 20 Hz - 20 kHz (±0 dB) and 1.5 Hz - 1 MHz (-3 dB). THD and IMD are 0.003% at full output. Rise and settling time is below 450 ns, and slew rate is 1,500 V/µs. Signal-to-noise ratio is above 90 dB for MM and above 81 dB for MC. Each unit measures 504 x 141 x 390 mm (W x H x D), and weights are 15.0 kg for the main unit and 17.1 kg for the power supply.

Engineering and use context

All amplification stages are dual mono, fully differential (balanced) and DC coupled in class A, without capacitors in the audio signal path and with zero overall feedback. Boards use 75 µm and 105 µm copper on all layers and are decoupled from the chassis with custom mechanical parts.

Input capacitance, input impedance (loading) and gain are set internally, separately for each channel and each input. Factory defaults are 50 pF, 660 ohms and 67 dB, and snap-in OPT positions accept custom resistors. On the front panel one rotary control selects the input with 0 or 180 degree absolute phase, and the other selects mute or one of the five EQ curves. Each input has its own ground terminal for one of up to three tonearms.

The power supply unit carries the master power switch, an IEC 15 A inlet, a 7-pin XLR connector for the umbilical and an AUDIO GND switch that connects or lifts the audio signal ground from mains earth. Critical Mass Systems CS2M feet are used, and the supplied 7-pin XLR umbilical is a Cardas cable.

Pairing

A line preamplifier with an XLR or RCA input is required. MM and MC cartridges connect directly, and up to three tonearms or turntables can stay connected.

Alternatives

The PHONOb is the smaller Master Collection phono stage, with one RCA and one XLR phono input.

Spezifikationen

  • Modellbezeichnung

    PHONOa

  • Eingänge (symmetrisch)

    3

  • Eingänge (unsymmetrisch)

    3

  • MC-Eingangsimpedanz (stromgekoppelt) (Ω)

    N/A

  • MM/MC-Eingangsimpedanz (spannungsgekoppelt) (Ω)

    N/A

  • Ausgangsimpedanz (Ω)

    90

  • Verstärkung (dB)

    from 48 to 71

  • Genauigkeit der Wiedergabe-Entzerrungskurven (dB)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    20

  • Obere Grenzfrequenz +/- 3dB (Hz)

    20 000

  • Klirrfaktor + Rauschen (%)

    0.003

  • Abmessungen (mm)

    504 x 141 x 390

  • Gewicht (kg)

    15

  • Offizieller Link

Weitere Komponenten