Hifiverse

Phonovorstufen - Kora PHONOSTAGE

Beschreibung, Bilder, technische Daten und Spezifikationen

Kora PHONOSTAGE
Bildquelle - (c) Kora

The Phono Stage is a solid-state phono preamplifier from Kora, designed and built in Toulouse, France. Kora describes it as an audio adaptation of the EPC1 D, an ultra-low-noise laboratory preamplifier built by its professional division. It accepts variable reluctance, moving magnet and moving coil cartridges on four individually programmable inputs. In France it was priced at EUR 6,600.

Key specs that matter

Inputs 1 and 2 are on XLR sockets and selectable balanced or unbalanced, and inputs 3 and 4 are unbalanced on RCA. Gain is programmable as a factor of 150, 300, 500, 750, 1,000, 1,500 or 3,000. Input impedance is 50 kohms or adjustable from 10 to 1,270 ohms in 10-ohm steps, and input capacitance is 0 - 1.5 nF in 0.1 nF steps. Input noise is 70 nV on the audio band and RIAA accuracy is ±1 dB. Maximum output voltage is 8 V RMS and output impedance is below 50 ohms. Two RCA and two XLR outputs can operate simultaneously. Chassis size is 320 x 75 x 260 mm (W x H x D), or 320 x 91 x 280 mm overall, and weight is 5 kg. Consumption is below 10 VA.

Engineering and use context

Kora set the goal of the lowest possible noise without an input transformer. Its fully symmetrical input stage uses low-noise input transistors rated at 0.5 nV/√Hz and has a programmable gain of 50 or 100. All resistors in the signal circuit are Vishay VSRJ metal foil types with accuracies down to 0.01%. A de-symmetrisation stage then converts the balanced signal to single-ended by analogue subtraction, removing part of the common-mode noise, and adds a gain of 3.

RIAA correction is split in two. The high-frequency part is fully passive with polystyrene capacitors, while an active circuit with polystyrene capacitors covers the low-frequency part. An output stage adds four programmable gains of 1, 3.33, 5 and 10, and a phase shifter creates the inverted signal for the XLR outputs.

Each input stores its gain, impedance, capacitance and connection type, and the unit recalls them at switch-on. Everything is set with a single press-and-turn button. A rumble filter with a -6 dB cut-off at 7 Hz is available. The demagnetisation mode acts on all four inputs at once while a record plays for half an hour. On loss of mains power the output is cut off instantly.

Pairing

A line-level input on RCA or XLR is required. Factory settings are MC at 200 ohms and gain 1,500 on inputs 1 and 3, and MM at 50 kohms and gain 150 on inputs 2 and 4. The XLR inputs accept a balanced cartridge connection.

Alternatives

The Kora Phono module is a drawer for the PR140 preamplifier with a single RCA input switchable between MM and MC.

Spezifikationen

  • Modellbezeichnung

    PHONOSTAGE

  • Eingänge (symmetrisch)

    2

  • Eingänge (unsymmetrisch)

    2

  • MC-Eingangsimpedanz (stromgekoppelt) (Ω)

    N/A

  • MM/MC-Eingangsimpedanz (spannungsgekoppelt) (Ω)

    50kΩ or adjustable from 10Ω to 1270Ω, in 10Ω steps

  • Ausgangsimpedanz (Ω)

    50

  • Verstärkung (dB)

    150 — 300 — 500 — 750 — 1000 — 1500 — 3000

  • Genauigkeit der Wiedergabe-Entzerrungskurven (dB)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    20

  • Obere Grenzfrequenz +/- 3dB (Hz)

    20 000

  • Klirrfaktor + Rauschen (%)

    N/A

  • Abmessungen (mm)

    320 × 75 × 260

  • Gewicht (kg)

    5.0

  • Offizieller Link