Hifiverse

Tonabnehmer - Benz Micro ZEBRA

Beschreibung, Bilder, technische Daten und Spezifikationen

Benz Micro ZEBRA
Bildquelle - (c) Benz Micro

The Zebra is a moving-coil cartridge from the Swiss cartridge specialist Benz Micro and the company's first new model in more than a decade. It takes its outer parts from the Ruby Z, above all the zebra wood body that gives the cartridge its name, and combines them with the generator of the Wood series. Three output versions are offered - Zebra L, Zebra M and Zebra H. In the current catalogue it sits next to the LP-S, the Ruby Z and the SLR Gullwing.

Key specs that matter

Output at 3.54 cm/s is 0.4 mV for the L, 0.8 mV for the M and 2.5 mV for the H, with internal impedance of 12, 24 and 95 ohms respectively. A solid boron rod cantilever of 0.28 mm diameter carries a mirror-polished nude diamond with a line-contact profile and a 3 x 60 µm tip. Frequency response is 20 Hz - 20 kHz (±1 dB), channel separation is better than 35 dB (1 kHz) and channel balance is within 0.5 dB. Dynamic compliance is 15 µm/mN. The cartridge weighs 9.6 g and the vertical tracking angle is 20 degrees. Tracking force is 1.7 - 2.0 g, with 1.7 - 1.8 g given as the optimum.

Engineering and use context

Its body is machined from zebra wood and vented. This wood is denser and more costly than the material of earlier Benz wooden bodies, and Benz Micro chose it for resonance control of the housing. Inside is the classic Benz generator on a pure iron cross, the same motor type as in the Wood SL, the direct predecessor of the Zebra L. Benz Micro uses solid boron cantilevers across its whole range for the combination of high stiffness and low mass.

Pairing

Zebra L and Zebra M require a dedicated MC phono stage or a step-up transformer, and the Zebra H runs into a standard MM input. Recommended load is 100 ohms - 47 kohms for the L and M and 1 kohm - 47 kohms for the H. Benz Micro specifies a tonearm of medium to high effective mass. The L needs a low-noise stage with high gain, and the M is the version for phono stages with moderate MC gain.

Alternatives

The Benz Micro Ruby Z is a moving-coil cartridge with the same zebra wood body, a square ruby coil plate and 0.34 mV output.

Spezifikationen

  • Modellbezeichnung

    ZEBRA

  • Typ

    MC

  • Nadel

    N/A

  • Gehäuse

    N/A

  • Nadelträger

    Boron

  • Spulen

    N/A

  • Ausgangsspannung (mV@5cm/sec)

    L = 0.4, M = 0.8 H = 2.5

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Innenwiderstand (Ohm)

    L = 12, M = 24, H = 95

  • Kanaltrennung (dB / 1,000 Hz)

    N/A

  • Nadelnachgiebigkeit (×10-6cm/dyne at 100Hz)

    N/A

  • Empfohlene Abschlussimpedanz (Ohm)

    N/A

  • Empfohlene Tonarme

    N/A

  • Gewicht (g)

    9.6

  • Offizieller Link