Hifiverse

Tonabnehmer - Dynavector Ultimate XV

Beschreibung, Bilder, technische Daten und Spezifikationen

Dynavector Ultimate XV
Bildquelle - (c) Dynavector

The Dynavector XV Ultima is a moving coil design of low output belonging to the XV series from Dynavector, and it follows the DRT XV-1t as the newest member of that range. It combines a multi-magnet Alnico motor, flux damping on the front yoke and an exposed, nude construction with a solid boron cantilever. Its US price is about USD 11,250.

Key specs that matter

Output is 0.32 mV at 1 kHz and 5 cm/s, while internal impedance measures 24 ohm, and Dynavector recommends a load above 75 ohm. The stylus is a PF line contact profile with a 7 x 30 micron radius, carried on a 6 mm solid boron cantilever. Frequency response is 20 Hz to 20,000 Hz within 1 dB. Channel separation reaches 30 dB at 1 kHz, with channel balance held to 1.0 dB. Compliance is 10 mm/N, the tracking force window runs from 1.8 g to 2.2 g, and the cartridge weighs 12 g.

Engineering and use context

The magnetic system uses eight Alnico magnets. Four of them form the main circuit through a V-shaped front yoke, and the other four sit beside the armature, one for each coil. The front yoke has a square aperture with slits at its corners, and the magnetic equaliser is divided into four sections so that every coil gets its own independent magnetic path. Two flux dampers, each a shorted wire wound around the front yoke, are fitted on either side of it to stabilise the two channel circuits, a design Dynavector holds a patent on. Yokes, equaliser and magnets all go through the company's Special Annealing treatment. The coil bobbin is made of research-grade, ultra-high-purity iron cut into a cross-armature shape to keep moving mass down, and it is wound with pure copper wire that Dynavector describes as thinner than a human hair. The inverted V body combines precision-machined aluminium with a laminated bamboo composite and carries a finish modelled on Japanese Urushi lacquer.

Pairing

The tiny signal has to be raised substantially before line level, so a high-gain moving coil phono stage is required, or alternatively a step-up transformer whose ratio matches a low-output coil. The medium-low compliance and fairly substantial body mass make a medium to heavy effective mass tonearm the natural match, and the uncovered magnet circuit and wiring call for a headshell and arm that allow precise alignment without touching the coil area.

Alternatives

The Dynavector DRT XV-1t, the model the XV Ultima replaces in the XV series, is rated at a slightly higher 0.35 mV output.

Spezifikationen

  • Modellbezeichnung

    Ultimate XV

  • Typ

    MC

  • Nadel

    PF Line contact shape, stylus radius: 7 x 30 micron

  • Gehäuse

    N/A

  • Nadelträger

    6mm length solid boron

  • Spulen

    N/A

  • Ausgangsspannung (mV@5cm/sec)

    0.32

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Innenwiderstand (Ohm)

    24

  • Kanaltrennung (dB / 1,000 Hz)

    30

  • Nadelnachgiebigkeit (×10-6cm/dyne at 100Hz)

    10 mm/N

  • Empfohlene Abschlussimpedanz (Ohm)

    >75

  • Empfohlene Tonarme

    N/A

  • Gewicht (g)

    12

  • Offizieller Link

Weitere Komponenten