Hifiverse

Standlautsprecher - Wilson Audio Sasha DAW

Beschreibung, Bilder, technische Daten und Spezifikationen

Wilson Audio Sasha DAW
Bildquelle - (c) Wilson Audio

The Sasha DAW is a two-module floorstanding loudspeaker from Wilson Audio Specialties of Provo, Utah, released in 2018 and retired in 2023. Wilson traces it to David A. Wilson's original WATT/Puppy, the lineal ancestor of the first Sasha, and DAW stands for Dave Andrew Wilson. It succeeded the Sasha 2 and was the first new product the company released after his death, with his son Daryl Wilson now running the firm. The European price was EUR 45,000 per pair.

Key specs that matter

Drive units are two 203 mm woofers, one 178 mm midrange and one 25 mm dome tweeter. The upper module is a rear-vented midrange enclosure built from X-Material and S-Material, while the woofer module is rear-ported and made of X-Material. Sensitivity is 91 dB (1 W/1 m, 1 kHz). Nominal impedance is 4 ohms, with a minimum of 2.48 ohms at 85 Hz. Wilson specifies a minimum amplifier power of 25 W per channel. Frequency response is 20 Hz - 30 kHz (±3 dB, room average response). Each speaker measures 1137 x 368 x 583 mm (H x W x D) and weighs 107 kg, and the system shipping weight is about 322 kg.

Engineering and use context

Its woofer is based on the 203 mm driver of the Alexia Series-2 and was redesigned for the Sasha. Midrange and tweeter are the same units used in the WAMM Master Chronosonic, joined to the woofers by an all-new crossover. X-Material is Wilson's proprietary composite for woofer and tweeter enclosures, and S-Material came out of the research for the original Sasha and was designed specifically for the midrange.

At the rear of the upper module a calibrated ladder, the Alignment Block, allows fine adjustment in the time domain. The upper module rests on a specific step of this block, chosen from Wilson's propagation delay tables according to listener ear height and distance, and spikes couple it to the woofer module. Two umbilicals run from the woofer module to separate midrange and tweeter connections on the upper module.

Behind an aluminium back cover on the woofer module sits the resistor plate. Tweeter level is set by two 6.0 ohm resistors in parallel and midrange level by two 4.8 ohm resistors in parallel, and Wilson states that these resistors also act as fuses that open before a driver is damaged by excess power. A woofer damping resistor is pre-installed in the base. Spikes for the woofer module can be assembled with or without the supplied Mechanical Diodes.

Pairing

An amplifier stable into loads below 4 ohms is required.

Alternatives

The Sasha V is the later Wilson Audio floorstanding loudspeaker in the Sasha line.

Spezifikationen

  • Modellbezeichnung

    Sasha DAW

  • Untere Grenzfrequenz +/- 3dB (Hz)

    20

  • Obere Grenzfrequenz +/- 3dB (Hz)

    30000

  • Empfindlichkeit (dB at 1 W/1m)

    91

  • Impedanz (Ohms)

    4

  • Anforderungen an den Endverstärker (W)

    >25

  • Verfügt über interne Verstärkung

    k. A.

  • Leistung der internen Verstärkung (W)

    N/A

  • Größe (sm)

    113.67 x 36.83 x 58.0

  • Gewicht (kg)

    107.05

  • Offizieller Link