Hifiverse

Standlautsprecher - Jean-Marie Reynaud Auralis

Beschreibung, Bilder, technische Daten und Spezifikationen

Jean-Marie Reynaud Auralis
Bildquelle - (c) Jean-Marie Reynaud

The Auralis is a floorstanding loudspeaker from Jean-Marie Reynaud (JMR), the French maker that has developed loudspeakers since 1967. JMR places it at the top of its range. It is designed, assembled, checked and tuned in the company's workshops in Charente. Pre-orders opened in 2025, first deliveries were scheduled for February 2026, and the price is EUR 18,000 per pair.

Key specs that matter

This is a 2.5-way design with two mid/bass units and a 120 mm AST tweeter. Frequency response is 30 Hz - 28 kHz, with 30 Hz quoted at -6 dB. Sensitivity is 89 dB SPL (2.83 V/1 m), nominal impedance is 8 ohms and minimum impedance is 4.3 ohms. Power handling is 250 W, with 400 W peak. Distortion is below 0.2% at an 85 dB level. Crossover slopes are 6, 12 and 12 dB per octave. Each speaker measures 300 x 1,150 x 420 mm (W x H x D) and weighs 45 kg. JMR specifies a listening area of 20 - 60 m2.

Engineering and use context

Both mid/bass units work together up to 220 Hz, and the tweeter is crossed over at 1.8 kHz with symmetrical 12 dB per octave slopes. SICA in Italy makes the mid/bass units to JMR's requirements. Their paper cone is derived from 1970s reference models and carries a rear-side treatment that damps it at the top of its band. Each unit has an open cast aluminium basket, a ventilated 38 mm voice coil on a high-temperature treated fibreglass former and an M-type constant-compliance surround. A solid aluminium phase plug is mounted on the unit that covers the midrange.

Bass loading is a proprietary tuned triangular line, a JMR principle, vented through a front port. Its cabinet uses HDF panels 25 - 40 mm thick, with a minimal amount of absorbent and viscoelastic compounds at chosen points. An epoxy resin pod houses the upper part of the tweeter. Instead of spikes, a decoupling base with no direct mechanical link carries the speaker, through a polymer element and Teflon pads.

JMR wires the crossover by hand without a printed circuit board and keeps the part count low. Main inductors are pure copper foil on beech formers, capacitors are ClarityCap PUR, and Path Audio resistors set the tweeter attenuation. Each of these resistors has a third grounded terminal and a copper tube that acts as electromagnetic shield and heatsink. The finish is Woodscore XO with a seven-layer high-gloss varnish, a black front and an HDF counter-front panel edged with a machined solid aluminium bead.

Pairing

The recommended amplifier power is 40 - 300 W. According to JMR, tube and solid-state amplifiers are both compatible, and its impedance curve shows very small variations. Connection is single-wire, with an extra crossover ground terminal.

Alternatives

The Orfeo Grande is another floorstanding loudspeaker in the current JMR range.

Spezifikationen

  • Modellbezeichnung

    Auralis

  • Untere Grenzfrequenz +/- 3dB (Hz)

    30

  • Obere Grenzfrequenz +/- 3dB (Hz)

    28 000

  • Empfindlichkeit (dB at 1 W/1m)

    89

  • Impedanz (Ohms)

    4

  • Anforderungen an den Endverstärker (W)

    40 - 300

  • Verfügt über interne Verstärkung

    k. A.

  • Leistung der internen Verstärkung (W)

    N/A

  • Größe (sm)

    115 x 42 x 30

  • Gewicht (kg)

    45

  • Offizieller Link