Hifiverse

Regallautsprecher - FiiO SP5

Beschreibung, Bilder, technische Daten und Spezifikationen

FiiO SP5
Bildquelle - (c) FiiO

The SP5 is a pair of active desktop speakers from FiiO, the Guangzhou maker of portable players, DACs and headphone amplifiers. It follows the smaller SP3 and has larger drivers and more amplifier power. One cabinet is the main speaker with the controls and inputs, the other is the secondary speaker, and an RJ45 data transmission cable links the two. Colours are black and white.

Key specs that matter

Each cabinet has a 133 mm composite fibre woofer and a 25 mm composite silk soft dome tweeter. Amplifier output is 60 W x 2 for the woofers and 20 W x 2 for the tweeters. Conversion uses two ES9068AS DAC chips, one per channel. Inputs are RCA, AUX, balanced XLR (XLR3 or TRS 6.35 mm) and Bluetooth 5.1 with SBC, AAC, aptX, aptX LL, aptX HD, LDAC and aptX Adaptive at up to 990 kbps. Volume range is +31.5 dB to -95 dB in 0.5 dB steps, and FiiO quotes a signal-to-noise ratio of 100 dB. Treble is set at -2, 0 or +2 dB, bass below 100 Hz at 0, +3 or +6 dB, and the low-frequency extension at 50 or 60 Hz.

Engineering and use context

According to FiiO, the woofer cone is a composite fibre similar to the Continuum material of B&W's 700 Series, and the magnetic circuit, suspension and voice coil were reworked as well. Inside the tweeter dome sits a soft hemispherical structure that absorbs energy from the back of the diaphragm. A large rear cavity lets the tweeter operate down to 800 Hz, and it has a waveguide and a magnetic fluid cooling and damping system.

Both speakers contain a Texas Instruments TPA3116D2 class D stereo amplifier with protection against short circuits, overheating and voltage fluctuations. Each one also has its own 120 W switching power supply with universal voltage support. Multi-stage rectification and filtering power the output stage, and a transformer stage derives a dual-symmetrical supply for the front-end circuitry. Volume is set by an NJW1195A resistor-ladder electronic volume control in each speaker, with output noise of -118 dBV and distortion of 0.0003%.

Every cabinet is die-cast at 650 degrees C from a single 10 kg aluminium ingot. Horizontal stripes on its surface act as structural reinforcement, and the drivers are angled for phase alignment. Bluetooth uses a Qualcomm QCC5125 chip, and the FIIO Control app sets the input, codec, RGB lighting, power saving and a 10-band PEQ. On the rear are a trigger input, a ground lift switch and an L/R channel switch. Two Furukawa oxygen-free copper power cables are included.

Pairing

A preamplifier with a trigger output can switch the SP5 on and off. An audio interface or console connects through the XLR input.

Alternatives

The FiiO SP3 is the brand's smaller active desktop speaker.

Spezifikationen

  • Modellbezeichnung

    SP5

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Empfindlichkeit (dB at 1 W/1m)

    N/A

  • Impedanz (Ohms)

    N/A

  • Anforderungen an den Endverstärker (W)

    N/A

  • Verfügt über interne Verstärkung

    Ja

  • Leistung der internen Verstärkung (W)

    60 + 20

  • Größe (sm)

    N/A

  • Gewicht (kg)

    N/A

  • Offizieller Link