Hifiverse

Kopfhörerverstärker - SMSL VMV P2 MK2

Beschreibung, Bilder, technische Daten und Spezifikationen

SMSL VMV P2 MK2
Bildquelle - (c) SMSL

The VMV P2 MK2 is a fully balanced desktop headphone amplifier from SMSL, sold under the company's VMV label. It succeeds the first VMV P2 and was launched alongside the D2R MK2 DAC as a matching pair, at a price of USD 1,160. Its pre-outputs also allow use as a preamplifier for active speakers.

Key specs that matter

Balanced output power is 14 W x 2 into 16 ohms, 8 W x 2 into 32 ohms, 1 W x 2 into 300 ohms and 500 mW x 2 into 600 ohms. Into the same loads the unbalanced output gives 4 W, 2 W, 300 mW and 150 mW per channel. THD+N is -123 dB, or 0.00006% (1 kHz, 32 ohms). Signal-to-noise ratio and dynamic range are both 135 dB. Frequency response is 20 Hz - 100 kHz (-0.5 dB). Input impedance is 47 kohms and headphone output impedance is near 0 ohm, with pre-output impedance of 44 ohms balanced and 22 ohms unbalanced. The chassis measures 280 x 51 x 235.7 mm (W x H x D) and weighs 3.25 kg, and power consumption is under 100 W (EN60065).

Engineering and use context

SMSL describes the circuit as a fully balanced design with four ultra-low distortion Precision Linear Feedback Circuits (PLFC). A total of 99 low-noise op-amps are used in parallel. Power comes from a built-in high-efficiency, low-noise switching power supply based on gallium nitride (GaN), and the unit runs on 100 - 240 V AC. Gain is switchable in three steps, -3, 6 and 24 dB on the balanced outputs and -9, 0 and 18 dB on the unbalanced output, and according to SMSL the low setting is optimised for IEMs. A specially designed volume potentiometer reduces channel deviation. High-precision resistors with low temperature drift are used. SMSL specifies the amplifier for planar magnetic and high-impedance dynamic headphones as well as sensitive IEMs.

Output switching is by a relay with a pop-free design. Protection covers DC offset, overvoltage and overload, and a flashing red indicator shows that a protection circuit has tripped. Two front buttons select input and standby, output and gain, and a steady red indicator marks standby. Firmware is updated over a USB port.

Pairing

Sources connect through one balanced XLR input and one RCA input. Headphone outputs are a 4.4 mm balanced socket, a 4-pin XLR and a 6.35 mm jack. The matching DAC is the D2R MK2. XLR and RCA pre-outputs connect active speakers or a power amplifier.

Alternatives

The original SMSL VMV P2 is the earlier fully balanced headphone amplifier of the same series.

Spezifikationen

  • Modellbezeichnung

    VMV P2 MK2

  • Maximale Leistung, 32 Ohm (mW RMS per channel)

    8000 (Balanced), 2000 (Unbalanced)

  • Maximale Leistung, 50 Ohm (mW RMS per channel)

    N/A

  • Maximale Leistung, 300 Ohm (mW RMS per channel)

    1000 (Balanced), 300 (Unbalanced)

  • Maximale Leistung, 600 Ohm (mW RMS per channel)

    500 (Balanced), 150 (Unbalanced)

  • Untere Grenzfrequenz +/- 3dB (Hz)

    20

  • Obere Grenzfrequenz +/- 3dB (Hz)

    100 000

  • Verstärkung (dBu)

    N/A

  • Klirrfaktor (THD) (% at 1V RMS, 300 ohms)

    0.00006 (at 1 kHz into 32 Ohms)

  • Signal-Rausch-Abstand (dB)

    135

  • Intermodulationsverzerrung (IMD) (%, CCIR, 300 Ohms)

    N/A

  • Übersprechen (dB, 20Hz-20KHz, 300 Ohms)

    N/A

  • Ausgangsimpedanz (Ohms)

    N/A

  • Abmessungen (mm)

    51 x 280 x 235.7

  • Gewicht (kg)

    3.25

  • Offizieller Link