Hifiverse

Kopfhörerverstärker - AudioValve Eartube Mark II

Beschreibung, Bilder, technische Daten und Spezifikationen

AudioValve Eartube Mark II
Bildquelle - (c) AudioValve

The Eartube Mark II is a tube headphone amplifier from AudioValve. AudioValve describes it as a small-power amplifier made specifically for headphones and as a development of its earlier Eartube models. The signal path contains only tubes, and semiconductors are limited to the power supply. A Mark II USB version is also made.

Key specs that matter

Output power is 2 x 3.5 W into 100 ohms, and headphones from 8 to 200 ohms are accepted. Power bandwidth is 8 Hz - 80 kHz. Signal-to-noise ratio is 100 dB, and channel separation is 70 dB. Two pairs of gold-plated RCA inputs are provided, input 1 with 14.5 dB of gain and input 2 with 21.5 dB, both at 47 kohms. Two Neutrik 6.3 mm headphone jacks on the front panel allow two listeners at once. Power consumption is 100 VA, and mains versions for 100 V and 245 V are built. The case measures 380 x 260 x 120 mm (W x D x H), and weight is 10 kg.

Engineering and use context

Three 6N3P double triodes form the input stage. Its output stage is a push-pull pair of QQE 03/12 power tetrodes in the long-life Siemens military version, operating in class A. Bias is regulated automatically, with no manual adjustment after a tube change, and AudioValve lists GU17, RS1023 and 6360 as equivalent output tubes. Power comes from a toroidal transformer, and the whole circuit is on one two-layer circuit board.

A switchable bass crossfeed filter mixes part of the left channel into the right and vice versa. AudioValve links this filter to lower listening fatigue on headphones. Volume is set by a large Alps logarithmic potentiometer, and a smaller knob next to it adjusts balance by up to 2 dB either way. A rocker switch on the front panel selects the source. About 30 seconds after switch-on the amplifier is ready, and stereo level meters on the front panel light up. Black and silver versions of the metal case are offered, and the case also shields the circuit from external interference. On the USB version, a player section for USB sticks, SD cards and FM radio is added, with its own remote control.

Pairing

Dynamic headphones within the rated load range connect directly. Input 2 is the higher-gain input for sources with a lower output level. Two gold-plated XLR sockets on the rear carry a volume-controlled signal, with pin 2 as the hot phase, for use as a preamplifier with separate power amplifiers. AudioValve states that the Eartube can also drive loudspeakers.

Alternatives

The RKV Mark II is AudioValve's output-transformerless headphone amplifier on four 6F5P tubes.

Spezifikationen

  • Modellbezeichnung

    Eartube Mark II

  • Maximale Leistung, 32 Ohm (mW RMS per channel)

    3500 (100 Ohms)

  • Maximale Leistung, 50 Ohm (mW RMS per channel)

    N/A

  • Maximale Leistung, 300 Ohm (mW RMS per channel)

    N/A

  • Maximale Leistung, 600 Ohm (mW RMS per channel)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    8

  • Obere Grenzfrequenz +/- 3dB (Hz)

    80 000

  • Verstärkung (dBu)

    N/A

  • Klirrfaktor (THD) (% at 1V RMS, 300 ohms)

    N/A

  • Signal-Rausch-Abstand (dB)

    100

  • Intermodulationsverzerrung (IMD) (%, CCIR, 300 Ohms)

    N/A

  • Übersprechen (dB, 20Hz-20KHz, 300 Ohms)

    N/A

  • Ausgangsimpedanz (Ohms)

    N/A

  • Abmessungen (mm)

    380 x 260 x 120

  • Gewicht (kg)

    10.0

  • Offizieller Link