Hifiverse

Vorverstärker - VTL TL 2.5i

Beschreibung, Bilder, technische Daten und Spezifikationen

VTL TL 2.5i
Bildquelle - (c) VTL

The TL-2.5i is the all-tube line preamplifier of VTL's Performance series, a revised version of the long-standing TL-2.5. VTL was founded in 1981 and is led by Luke Manley, and the TL-2.5i is hand-built in its factory in California. A phono stage for MM and MC cartridges is optional and can be retro-fitted internally.

Key specs that matter

The line stage uses two 12AU7 and two 12AT7 tubes. Gain is 8 dB or 14 dB (user-selectable), and maximum output voltage is 30 V RMS. THD is below 0.02% (20 Hz - 20 kHz), S/N ratio is 90 dB, and channel separation is 75 dB at 1 kHz. Input impedance is 50 kohm and output impedance is 200 ohms. Connections are 6 line inputs (5 with phono), 2 pairs of single-ended RCA outputs, 1 tape loop, 1 record output and 1 external processor loop for home theater. Power consumption is 100 W, or 150 W with the phono stage. Dimensions are 483 x 381 x 102 mm (W x D x H), and VTL lists the weight as 11.3 kg.

Engineering and use context

It is a pure tube circuit with a high-current, low-impedance output, and VTL states that it drives amplifier loads down to 45 kohm without audible bass roll-off. Each gain stage has its own stiff power supply, the supplies are well shielded, and the power transformer is an ultra-low-radiation design. Volume and balance use 27 mm laser-trimmed controls. A Normal/Low switch selects the gain, a mono function works on line and phono inputs, and the standard remote control covers volume and mute.

In the optional phono stage the MM section uses two 12AX7 tubes, with 37 dB of gain, 47 or 100 kohm loading and 80 dB S/N. Active MC mode adds one 12AU7 and gives 52 or 58 dB, with loads of 100 ohms, 470 ohms, 1 kohm, 4.7 kohm and 47 kohm and 70 dB S/N. A user-selectable MC step-up transformer gives 60 dB, loads of 100 ohms, 470 ohms and 1 kohm and 75 dB S/N. The phono circuit is a low-noise hybrid JFET design with improved filtering against RF interference.

Construction uses VTL gold-plated RCA jacks, a glass fibre circuit board with heavy copper traces and a heavy 16-gauge chassis. The IEC power cord is detachable, and silver or black cosmetics are offered.

Pairing

Power amplifiers with single-ended RCA inputs are required. The second pair of RCA outputs allows a second power amplifier or a subwoofer. A surround processor connects through the processor loop.

Alternatives

The TL-5.5 Series II Signature is the next VTL preamplifier up the range.

Spezifikationen

  • Modellbezeichnung

    TL 2.5i Performance

  • Analogeingänge (symmetrisch)

    N/A

  • Analogeingänge (unsymmetrisch)

    8

  • Analogausgänge (symmetrisch)

    N/A

  • Analogausgänge (unsymmetrisch)

    2

  • Verstärkung (dBu)

    8dB or 14dB

  • Eingangsempfindlichkeit (mV)

    N/A

  • Ausgangsspannung (V)

    30

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    50 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    200

  • Maximaler Ausgangspegel (symmetrisch) (dBu)

    N/A

  • Maximaler Ausgangspegel (unsymmetrisch) (dBu)

    N/A

  • Regelbereich der Lautstärke (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    20

  • Obere Grenzfrequenz +/- 3dB (Hz)

    20 000

  • Signal-Rausch-Abstand (SNR, unbewertet) (dB)

    90

  • Klirrfaktor + Rauschen (THD+N) (%)

    < 0.02

  • Abmessungen (mm)

    483 x 381 x 102

  • Gewicht (kg)

    11.34

  • Offizieller Link

Weitere Komponenten