Hifiverse

Vorverstärker - Exposure 5010 Pre-Amplifier

Beschreibung, Bilder, technische Daten und Spezifikationen

Exposure 5010 Pre-Amplifier
Bildquelle - (c) Exposure

The 5010 Pre-Amplifier is a stereo line preamplifier from Exposure, the British company founded by John Farlowe in 1974. Exposure released the 5010 Series in 2018 as a pre-amplifier and mono amplifiers, following the MCX Series of 2008 at the head of the range. The front panel carries a power switch, a source selection knob and a volume control knob, and the case was offered in black or titanium.

Key specs that matter

Gain (1 kHz) is +9 dB at the unbalanced outputs and +15 dB at the balanced output. Sensitivity is 500 mV, and maximum output is above 9 V RMS unbalanced. Frequency response is -3 dB at 1 Hz and 57 kHz (ref. 1 kHz, max volume). THD is below 0.005% (1.6 V RMS output, 1 kHz), and signal-to-noise ratio is above 98 dB (A-weighted, ref. 1.6 V RMS output). Channel separation is above 60 dB from 20 Hz to 20 kHz, typically above 85 dB at 1 kHz. Power consumption is below 25 W. Dimensions are 440 x 90 x 300 mm (W x H x D, including knob), and net weight is 6 kg.

Engineering and use context

Six line-level RCA inputs are provided, labelled PHONO/AUX 1, TUNER, CD, AUX 2, AV and TAPE PLAY. An optional MM or MC phono module or a DAC module plugs into the main circuit board. Next to the inputs is a ground terminal for a turntable arm ground wire.

Its AV input has fixed gain for connection to AV receivers. When AV is selected, the volume control has no effect and the volume LED goes out.

On the output side there are balanced outputs, two pairs of RCA pre-amp outputs (PRE OUT 1 and 2) and a TAPE REC output for recording. An output relay activates after a short delay at switch-on. LEDs on the volume knob and next to each source show the current setting, and the knob LED flashes while the volume changes.

Supplied with the unit is the HS3 remote control, which covers volume, mute and input selection and also has functions for an Exposure CD player, the 2010S2 DSD DAC and the XM Series. Each unit leaves the factory set for one mains voltage range, 110/120 V or 220/240 V. The Exposure warranty covers parts and labour for three years from the date of purchase.

Pairing

The balanced outputs connect to a power amplifier with balanced inputs. Two RCA pre-amp outputs allow bi-amping with mono or stereo power amplifiers. A turntable requires the optional MM or MC phono module.

Alternatives

The 3010S2D Pre-Amplifier, released in 2014, is the smaller Exposure preamplifier.

Spezifikationen

  • Modellbezeichnung

    5010 Pre-Amplifier

  • Analogeingänge (symmetrisch)

    N/A

  • Analogeingänge (unsymmetrisch)

    5 + 1 (Phono)

  • Analogausgänge (symmetrisch)

    N/A

  • Analogausgänge (unsymmetrisch)

    N/A

  • Verstärkung (dBu)

    15

  • Eingangsempfindlichkeit (mV)

    500

  • Ausgangsspannung (V)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    18 000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    18 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Ausgangspegel (symmetrisch) (dBu)

    N/A

  • Maximaler Ausgangspegel (unsymmetrisch) (dBu)

    N/A

  • Regelbereich der Lautstärke (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (SNR, unbewertet) (dB)

    >98

  • Klirrfaktor + Rauschen (THD+N) (%)

    <0.005

  • Abmessungen (mm)

    90 x 440 x 300

  • Gewicht (kg)

    6

  • Offizieller Link