Hifiverse

Endstufen Stereo - Cayin Soul 170P

Beschreibung, Bilder, technische Daten und Spezifikationen

Cayin Soul 170P
Bildquelle - (c) Cayin

The Soul 170P is a stereo tube power amplifier that Cayin calls the flagship Class A push-pull KT170 tube power amplifier of its Soul Series. It is the first Soul Series amplifier with Class A amplification, and its companion is the Soul 170C tube preamplifier. Launch was set for November 2025 at EUR 7,500, in matte black with side panels of solid North American walnut.

Key specs that matter

Its output stage uses four TUNG-SOL KT170 beam tetrodes in Class A push-pull. Rated output power is 2 x 32 W RMS in triode mode and 2 x 60 W RMS in ultralinear mode, or 64 W and 120 W RMS in mono mode. Frequency response is 8 Hz - 70 kHz (-3 dB, RCA/XLR). Total harmonic distortion is 0.2% (1 W/1 kHz) and less than 2% at rated output power. Signal-to-noise ratio is 105 dB (RCA, A-weighted) and 102 dB (XLR, A-weighted). Input sensitivity is 820 mV (NFB low) or 960 mV (NFB high), and input impedance is 18 kohms. Dimensions are 430 x 420 x 238 mm, net weight is 37.5 kg and maximum power consumption is 420 W.

Engineering and use context

Two JJ 12AU7 tubes form the voltage amplification stage, and the driver stage uses two JJ 6SN7. A 17AX4GT rectifier tube supplies DC voltage to the driver stage. Cayin applies a moderate global negative feedback loop with two selectable NFB levels, High and Low.

A Dynamic Auto Bias servo circuit regulates the operating status of each KT170, and the power tubes are replaced without manual adjustment. Stereo or mono operation is selected with a rear-panel switch. Each amplifier is hand-assembled with point-to-point wiring and silver-plated internal wiring. Inside are a customised hand-wound toroidal power transformer and EI wide-band output transformers, and aluminium alloy anti-resonance feet support the chassis.

Protection includes a tube soft-start circuit with a 60-second delay, MCU-controlled protection logic and BMI indicators. These indicators detect power tube faults and engage a safety mode automatically. Connections are one pair of XLR inputs, one pair of RCA inputs and 4 ohm and 8 ohm speaker terminals.

Pairing

A line-level preamplifier or a DAC with volume control is required. The matching preamplifier is the Soul 170C. Its 4 ohm and 8 ohm taps accept speakers of either nominal impedance. Two chassis in mono mode form a pair of monoblocks.

Alternatives

Cayin's current range lists no other stereo power amplifier.

Spezifikationen

  • Modellbezeichnung

    Soul 170P

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    18 000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    18 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    60 + 120 (Mono)

  • Ausgangsleistung (4Ω) (W)

    N/A

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    8

  • Obere Grenzfrequenz +/- 3dB (Hz)

    70 000

  • Signal-Rausch-Abstand (dB)

    105

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    0,2

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    430 х 238 x 420

  • Gewicht (kg)

    37.5

  • Offizieller Link