Hifiverse

Endstufen Stereo - Constellation Audio Performance 2 Stereo Amplifier

Beschreibung, Bilder, technische Daten und Spezifikationen

Constellation Audio Performance 2 Stereo Amplifier
Bildquelle - (c) Constellation Audio

The Performance 2 Stereo Amplifier is a solid-state stereo power amplifier from Constellation Audio, one of the two power amplifiers of the Performance 2 series. Its companion is the Performance 2 Monoblock, rated at 1,200 W into 8 ohms and 2,000 W into 4 ohms. Constellation states that both exceed the original Performance amplifiers and the outgoing Reference series. Large power meters on the front panel are new to the series.

Key specs that matter

Maximum power is 600 W per channel into 8 ohms and 1,125 W per channel into 4 ohms (0.1% THD+N, 20 Hz - 20 kHz). Inputs are 4 XLR (2 Direct) and 2 RCA. Frequency response is 10 Hz - 80 kHz (±0.05 dB). Gain is 12 dB on the Direct input and 25.2 dB on the other inputs. Damping factor is above 160, and output impedance is 0.05 ohm. Signal-to-noise ratio (DC - 90 kHz) is above 100 dB A-weighted referred to 1 V and above 125 dB A-weighted referred to full power. AC power draw is 135 W at idle and 1,970 W at maximum power into 4 ohms. Dimensions are 47.6 x 28.6 x 57.2 cm (W x H x D), and weight is 40.9 kg.

Engineering and use context

Constellation calls its output topology Balanced Bridged. Each channel has separate amplifier circuits for the positive and negative halves of the signal. Other balanced amplifiers use N-type transistors for the positive half and P-type transistors for the negative half, while this design uses only N-type transistors, so both halves pass through the same circuitry.

At the input is the Line Stage Gain Module, with hand-matched low-noise transistors and a servo circuit that corrects signal balance inconsistencies. The Constellation Direct XLR input removes one amplification stage from the signal path and is designed for Constellation preamplifiers.

Power comes from the C-SMPS switch-mode power supply with Power Factor Correction (PFC). Power factor is 0.98 at partial power and 1.0 at full power, and the supply works at any AC mains voltage. Compared with the previous version, output power is 20 percent higher, and Constellation quotes noise more than 20 dB lower than a typical linear power supply. A 12 V DC trigger input is provided.

Pairing

The Direct input matches the Constellation Performance 2 Preamplifier. Each channel has one pair of binding posts for spade lugs or banana plugs, and bi-wiring requires stacked cables. A subwoofer must not be connected to these outputs through speaker-level inputs with grounded negative terminals.

Alternatives

The Constellation Revelation 2 Stereo Amplifier is a stereo power amplifier from the Revelation series.

Spezifikationen

  • Modellbezeichnung

    Performance 2 Stereo Amplifier

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    600

  • Ausgangsleistung (4Ω) (W)

    1125

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    1

  • Obere Grenzfrequenz +/- 3dB (Hz)

    100 000

  • Signal-Rausch-Abstand (dB)

    >115

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    <0,03

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    >500

  • Abmessungen (mm)

    432 x 191 x 609

  • Gewicht (kg)

    45,4

  • Offizieller Link