Hifiverse

Endstufen Stereo - Onkyo Icon M-80

Beschreibung, Bilder, technische Daten und Spezifikationen

Onkyo Icon M-80
Bildquelle - (c) Onkyo

The Onkyo Icon M-80 is a two-channel Class AB power amplifier from the Icon Series, introduced at CES 2025 together with the P-80 network preamplifier and the A-50 integrated amplifier. Launch price was USD 1,999. The M-80 is the first power amplifier of the series, which marked Onkyo's return to separate hi-fi components, and it comes in black or silver.

Key specs that matter

Output power is 130 W per channel into 8 ohms (FTC, 20 Hz - 20 kHz, 0.08% THD, both channels driven) and 200 W per channel into 4 ohms (1 kHz, 0.7% THD, both channels driven). Frequency response is 5 Hz - 100 kHz (+1 dB/-3 dB), and the signal-to-noise ratio is 106 dB (IHF-A). Input sensitivity is 1000 mV at 52 kohms on the RCA input and 1000 mV at 20 kohms on the XLR input. There are two sets of speaker terminals, SPEAKERS A and B, rated for 4 - 16 ohms each and for 8 - 16 ohms with A+B in use. A 12 V trigger input on a 3.5 mm jack is provided. Power consumption is 445 W, 51 W at idle and below 0.3 W in standby. The amplifier measures 435 x 135 x 345 mm (W x H x D) and weighs 13.5 kg.

Engineering and use context

Onkyo uses a three-stage Inverted Darlington Amplifier with a very low output impedance. Negative feedback is kept low, and Onkyo states that the amplifier is therefore not affected by noise from the speaker. Its output stage transistors are in parallel configuration for instantaneous current supply. In the driver stage, DIDRC (Dynamic Intermodulation Distortion Reduction Circuitry) with a high slew rate design reduces noise in the ultra-high frequency band.

The M-80 is powered by a custom high current power supply with 10,000 µF capacitors custom-made for Onkyo, and copper bus bars carry the current. An extruded aluminium heat sink is shaped to suppress vibration. Its housing consists of two aluminium side panels and a steel top panel, and Onkyo says this three-piece construction increases rigidity. Speaker and input terminals are hi-fi grade. The backlit power meters have a x1/x10 range switch and read the actual output into 8 ohm speakers. An INPUT SELECT switch chooses between the balanced and unbalanced inputs, and Auto Standby puts the amplifier into standby after 20 minutes without a signal.

Pairing

The matching preamplifier is the Icon P-80, connected over XLR or RCA. Two pairs of speakers can be connected and selected with the SPEAKERS button on the front panel. Onkyo names the Klipsch Forte as an example speaker for the P-80 and M-80 pair.

Alternatives

The Onkyo Icon A-50 is the network integrated amplifier of the same series.

Spezifikationen

  • Modellbezeichnung

    Icon M-80

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    2 x 130

  • Ausgangsleistung (4Ω) (W)

    2 x 200

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    N/A

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    N/A

  • Gewicht (kg)

    N/A

  • Offizieller Link