Hifiverse

Endstufen Stereo - Emm Labs EMM Labs MTRS

Beschreibung, Bilder, technische Daten und Spezifikationen

Emm Labs EMM Labs MTRS
Bildquelle - (c) Emm Labs

MTRS is a stereo power amplifier from EMM Labs. Like the MTRX and MTRX2 reference amplifiers, it is designed, manufactured and built in Canada. Its output stage uses Ed Meitner's completely redesigned high-current Meitner Power Driver. Silver and Black finishes are available, and pricing is on request.

Key specs that matter

Output power into 4 ohms is 400 W dynamic (RS-490 EIA) and 330 W RMS continuous. Voltage gain is 30 dB. Frequency response is 0.1 Hz - 200 kHz at full rated power. Signal-to-noise ratio is greater than 120 dB (A-weighted). THD+N and IMD are both below 0.01% (20 Hz - 20 kHz, full rated power), slew rate is greater than 100 V/µs and damping factor is greater than 200. Input impedance is 100 kOhm balanced (XLR) and 47 kOhm unbalanced (RCA). Dimensions are 544 x 584 x 297 mm (W x D x H), and weight is 82 kg.

Engineering and use context

The MTRS is a Class A/B solid-state design with fully discrete circuits and fully balanced audio paths throughout. Its circuits are built on custom ceramic PCB boards. According to EMM Labs, the amplifier drives the most severe loads with no overall feedback and can drive low-impedance loudspeakers down to 1 ohm. Real-time protection guards against speaker and amplifier damage.

A new proprietary power system is connected through a 30A 250V 3-pin IP44 power inlet of IEC60309 type. Mains voltage is factory set to 100, 115 or 240 V, 50/60 Hz. On the rear panel each channel has a balanced XLR input, an unbalanced RCA input and a set of Furutech binding posts, and an RS-232 port is provided for communication. Each amplifier ships in a custom EMM Labs flight case together with a custom Kimber Kable 30A power cable.

Pairing

A preamplifier with balanced XLR or unbalanced RCA outputs is required. The mains supply must accept the 30A IEC60309 power inlet. Loudspeakers with a low minimum impedance are within the stated drive capability.

Alternatives

The MTRX2 is the reference power amplifier in the EMM Labs range.

Spezifikationen

  • Modellbezeichnung

    EMM Labs MTRS

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    100 000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    47 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    N/A

  • Ausgangsleistung (4Ω) (W)

    400

  • Verstärkung (dBu)

    30

  • Untere Grenzfrequenz +/- 3dB (Hz)

    0,1

  • Obere Grenzfrequenz +/- 3dB (Hz)

    200 000

  • Signal-Rausch-Abstand (dB)

    120

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    0,01

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    200

  • Abmessungen (mm)

    544 x 584 x 297

  • Gewicht (kg)

    82

  • Offizieller Link